Volvo Penta 13L Скачать руководство пользователя страница 66

Страница: 66 / 122

EATS Inducements

TAD1360-65VE

Low tank level

1 When the level in the DEF tank falls to 23%, a warning lamp lights up.

2 When the tank level falls to 8% the warning lamp will flash and after 60 minutes engine speed will drop to

idle.

3 If the engine is started when the tank level falls below 8%, the engine will only run at idle.

4 For the engine to revert to full power the tank level must be above 14%. The tank level must be above 29%

for the system to extinguish the warning lamp and cancel the fault message.

DEF quality, alternative 1 (standard)

A. Engine rpm and torque
B. Time axis

1 A fault is detected and the warning lamp lights up.

2 After 60 minutes engine speed drops to idle. Ramp-down takes around 10 minutes.

3 If the fault is not remedied the engine will run at full power for 60 minutes after the first restart, and then drop

to idle.

4 Depending on the installation, it is possible to manually override the system action and run the engine at full

power for 30 minutes, after which the engine will drop to idle.

5 After the second restart the engine will run at full power for 60 minutes. Engine will speed again drop to idle;

service tools are required to reset the system.

Fault handling

47711089 09-2018 © AB VOLVO PENTA

Содержание 13L



























































































































Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды

Volvo Penta 13L, Руководство оператора

Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды