Volvo Penta 13L Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 122

background image

Before welding work

IMPORTANT:

Before any work with electric weld can begin, the
connection to all control units must be disconnected.
After finished welding, re-connect the connection to all
control units before connecting any battery cable.

Before any work on the cooling system

WARNING!

Stop the engine and let it cool before starting work on
the cooling system. Hot fluids and hot surfaces can
cause burns.

Hot coolant under pressure

CAUTION!

Hot coolant can cause burns. Avoid opening the filler
cap for the coolant when the engine is still hot. Steam
or hot coolant can spray out and system pressure is
lost.

Open the filler cap slowly and release the pressure in
the cooling system if the filler cap or valve must be
opened – or if a plug or a coolant hose must be
removed from a hot engine.

Hot oil under pressure

CAUTION!

Hot oil can cause burns. Avoid getting hot oil on the
skin. Ensure that the lubrication system is not
pressurized before starting any work. Never start or
operate the engine without the oil filler cap is on. There
is a risk that hot oil can spray out.

Refueling

WARNING!

There is always a risk of fire and explosion during
refueling. Smoking is forbidden and the engine must
be stopped.

Safety Information

10

47711089 09-2018 © AB VOLVO PENTA

«
...
10
11
12
13
14
...
»

Содержание 13L



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 13L

Бренд: Waukesha Страницы: 142

Бренд: Saito Страницы: 4

695D/925 Series

Бренд: Wisco Industries Страницы: 6

Бренд: Moons' Страницы: 28

Бренд: SOMFY Страницы: 48

Бренд: Kubota Страницы: 309

Бренд: Lycoming Страницы: 38

Бренд: Valach Страницы: 24

Бренд: Sisu Diesel Страницы: 80

Бренд: MULTIPLEX modell Страницы: 11

Бренд: Baumuller Страницы: 26

Бренд: Baumuller Страницы: 33

Бренд: Johnson Страницы: 56

Бренд: Honda Страницы: 5

Бренд: Honda Страницы: 60

Бренд: Alutech Страницы: 32

Бренд: Honda Страницы: 42

Бренд: Golden Eagle Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды