Volvo Penta 13L Скачать руководство пользователя страница 55

Страница: 55 / 122

Auxiliary Stop

For location of the extra stop, refer to

Maintenance, page 76

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

After Engine Shutdown

1 Check the engine and engine compartment for

leaks.

2 Turn off the main switches before any long

stoppage.

3 Carry out maintenance in accordance with the

schedule.

For longer breaks in operation

During longer breaks in operation, it is recommended
that the engine is warmed up at least once every two
weeks. This prevents corrosion in the engine.
If you expect the engine to be unused for two months
or more, it should be conserved. Refer to

Storage, page 106

IMPORTANT:

If there is a risk of freezing, the coolant in the cooling
system must have adequate antifreeze protection.

Refer to

Maintenance, page 89

IMPORTANT:

A poorly charged battery can freeze and burst.

Refer to

Battery, Charging

Engine Shutdown

47711089 09-2018 © AB VOLVO PENTA

Содержание 13L



























































































































Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды

Volvo Penta 13L, Руководство оператора

Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды