Volvo Penta 13L Скачать руководство пользователя страница 48

Страница: 48 / 122

Starting the Engine

The pre-heating time is adjusted to suit the engine
temperature, and can last for up to 50 seconds both
before and after starting.

The starter motor connection time is maximized to 20
seconds. After that, the starter motor circuit is
temporarily cut to protect the starter motor against
overheating.

DCU (Display Control Unit)

TAD1360-65VE

With pre-heating

1 Depress the

ON/OFF

-button (6).

2 Press the

SEL

button (8) to come to the

mainmenu.

3 Scroll down to

Pre/heater

with scroll button

(7),press

SEL

-button (8)

4 In the

pre-heater

menu, press the

SEL

-button

(8) to select pre-heating.

5 Press the

START

- button (2).

Without pre-heating

1 Depress the

ON/OFF

-button (6).

2 Press the

START

-button (2).

Leave the engine to idle for the first 10 seconds. Then
warm the engine up at low speed and under low load.
Never race the engine when it is cold.

Starting

47711089 09-2018 © AB VOLVO PENTA

Содержание 13L



























































































































Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды

Volvo Penta 13L, Руководство оператора

Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды