Volvo Penta 13L Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 122

background image

Oil level, checking and topping up

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

•

Normally the oil level is to be checked when the
engine is stopped. Wait a few minutes before
reading off the level, so that the oil has time to run
down into the oil sump.

•

Dipstick marked

STOP/OPERATING

can be read

both when the engine is stopped and when it is
running. Use the STOP side of the dipstick when the
engine is stopped and the OPERATING side when
in operation.

•

The oil level must be inside the marked area on the
dipstick. Never fill above the maximum limit on the
oil dipstick.

•

Only fill oil when the engine is stopped.

•

Only use Volvo Penta recommended oils; refer to

Technical Data, page 109

•

The oil level sensor only measures the oil level when
the ignition is switched to on, not continuously
during operation.

Checking the oil with a flexible dipstick

IMPORTANT:

Insert the dipstick in increments of around 200 mm,
without bending the wire, for the entire length of the
plastic tube.

P0026405

Maintenance

82

47711089 09-2018 © AB VOLVO PENTA

«
...
82
83
84
85
86
...
»

Содержание 13L



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 13L

Бренд: BAFANG Страницы: 4

Бренд: Mitsubishi Страницы: 176

Бренд: FAAC Страницы: 7

MAX-61SX-H RING WC Series

Бренд: O.S. engine Страницы: 36

Crankcase for Harley-Davidson

Бренд: S&S Cycle Страницы: 12

Бренд: RenewAire Страницы: 28

Бренд: M.T.H. Страницы: 26

Бренд: Geely Страницы: 198

Бренд: Siemens Страницы: 4

SIMOTICS A-1FV5

Бренд: Siemens Страницы: 66

Бренд: Siemens Страницы: 56

SIMODRIVE POSMO A

Бренд: Siemens Страницы: 58

Бренд: Siemens Страницы: 100

Simotics HV C 1NA14544WA600AG0-Z

Бренд: Siemens Страницы: 112

SIMOTICS DP 1PC13

Бренд: Siemens Страницы: 100

SIMOTICS DP 1PC134

Бренд: Siemens Страницы: 120

SIMOTICS HT Series

Бренд: Siemens Страницы: 128

Бренд: Siemens Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды