Volvo Penta 13L Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 122

background image

Menus

ENGINE DATA (ENGINE DATA)

Engine data shown may vary depending on the engine
installation.

•

Engine Hours

(Engine Hour) (tim)

•

Engine Speed

(Engine Speed) (rpm)

•

Coolant Temperature

(Coolant Temperature) (°C)

•

Oil Pressure

(Oil Pressure) (kPa)

•

Fuel Rate

(Fuel Rate) (l/h)

Current fuel consumption.

•

Boost Temperature

(Boost Temperature) (°C)

•

Boost Pressure

(Boost Pressure) (kPa)

•

Oil Temperature

(Oil Temperature) (°C)

DIAGNOSTICS (DIAGNOSTICS)

If the system detects a malfunction, the operator is
informed via a pop-up message on the display. The
fault codes are listed in the diagnostics menu; active
fault codes are at the top of the list and are denoted be
a green dot. For more information regarding cause and
remedies, use the arrow button to scroll to the fault
concerned and press

OK

. This will also provied

information about number of engine hours when the
fault became active and the SPN and FMI codes.

SETTINGS (SETTINGS)

Display (Display)

•

Set backlight time

(Set backlight time). On/OFF,

sets backlight to run in standby mode.

On

is the

default setting.

•

Set backlight brightness

(Set backlight

brightness). Adjust display backlight brightness
using the panel arrow buttons.

•

Set Instrument Brightness

(Set Instrument

Brightness). Sets backlighting in the display
instrument.

•

Change background color

(Change background

color). Select background color, gray or white.

Language (Language)

Sets the display language; chooses between English,
French, German, Spanish and Chinese.

ENGINE DATA

Engine Hours

Engine

Speed

Fuel Rate
Oil Pressure
Oil Temperature

1500

rpm

1536h

112 1/h

425 kpa

65 C

P 18291

00

Instruments and Controls

38

47711089 09-2018 © AB VOLVO PENTA

«
...
38
39
40
41
42
...
»

Содержание 13L



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 13L

Бренд: FAAC Страницы: 7

Бренд: Eaton Страницы: 16

NIIGATA MG(L)26HLX

Бренд: IHI Страницы: 204

Бренд: Texas Equipment Страницы: 38

Бренд: Dietz Страницы: 12

Бренд: Wood-mizer Страницы: 134

Бренд: Applied Motion Products Страницы: 2

Бренд: HandI Move Страницы: 26

Бренд: Mitsubishi Страницы: 96

Бренд: Vanguard Страницы: 36

Бренд: Varvel Страницы: 32

Бренд: IMS Страницы: 98

Бренд: Inel Страницы: 3

Бренд: Inel Страницы: 4

Бренд: Yamaha Страницы: 345

Бренд: Hornbach Страницы: 37

Бренд: Mercury Страницы: 132

Бренд: IronHorse Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды