background image

1

USERS INSTRUCTIONS

1.1 GAS APPLIANCES

Gas Safety (Installation and Use) Regulation (UK).

In the interests of your safety and that of others it is a legal 

requirement that all gas appliances are installed and correctly 

maintained by a competent person and in accordance with the 

latest regulations.

1.2 ELECTRICAL SUPPLY

Please ensure that this appliance has been properly connected 

to the electrical supply by means of a double pole isolator or 

un-switched socket, and that the correct size of fuse (3 AMP) 

has been 

fi

 tted.

Warning: this appliance must be earthed!

  

1.3 GUARANTEE REGISTRATION CARD

Please take the time to 

fi

 ll out your guarantee registration card. 

The completed warranty card should be posted within 30 days 

of installation.

1.4 APPLIANCE COMMISSIONING CHECKLIST 

(UK only)

A checklist section can be found at the rear of the appliance 

installation booklet. This important document must be com-

pleted during the installation/commissioning of your boiler. All 

GAS SAFE registered installers carry a GAS SAFE ID card, 

and have a registration number. These details should be re-

corded in the Benchmark commissioning checklist section 

within the installation booklet. You can check your installers 

details by calling GAS SAFE direct on 08004085500. Failure 

to install and commission the appliance in accordance with 

the manufacturers instructions will invalidate the warranty. 

This does not affect your statutory rights.

1.5 HOW DOES IT WORK?

Your 

Unica

 

boiler supplies heated water to your radiators and 

hot water to your hot water taps. The central heating is con-

trolled via a time clock and any thermostats that your installer 

may have 

fi

 tted.  The boiler will light when it receives a request 

from the time clock via any thermostat that may be installed, or 

whenever a hot water outlet (tap) is opened. Your 

Unica

 

 boiler 

lights electronically and does not have a pilot light.

In the unlikely event of a fault developing with your boiler, the 

supply of gas to the burner will be terminated automatically.

Dear Customer

Your Vokèra 

Unica

 

 boiler has been designed to meet and exceed the very latest standards in gas central heating technology, 

and if cared for, will give years of reliable use and ef

fi

 ciency.  

Please therefore take some time to read these instructions carefully.

Do’s and Don’t’s

Do

 ensure that the system pressure is periodically checked

Do

 ensure that the boiler should not be used by children or unassisted disabled people

Do

 ensure that you know how to isolate the appliance in an emergency

Do

 ensure that you are familiar with the appliance controls

Do

 ensure that your installer has completed the appliance log book section

Do not

 attempt to remove the appliance casing or gain internal access

Do not

 hang clothes etc. over the appliance

Do not

 forget to have the appliance serviced annually.

This booklet is an integral part of the appliance. It is therefore necessary to ensure that the booklet is handed to the person re-

sponsible for the property in which the appliance is located/installed. A replacement copy can be obtained from Vokèra customer 

services.

INTRODUCTION

1.6 DIMENSIONS

1.7 CLEARANCES REQUIRED

1.8 FROST PROTECTION SYSTEM

The 

Unica

 

is equipped with a built-in frost protection system, 

this enables the boiler to over-ride the time controls – even if 

switched off – and operate the burner and/or pump, should 

the temperature drop below 5

0

C for the main and for the DHW 

line. In particular the burner will be in ON status until the main 

temperature reaches 35°C for CH appliance and 55°C for 

DHW appliance.

 

Please note that the frost protection system 

is designed to protect the appliance only, should frost protec-

tion be required for the heating system, additional controls 

may be required.

NOTE

The frost protection system is reliant on the appliance having a 

permanent electrical supply, and being in a non-fault condition.

1.9 APPLIANCE STATUS INDICATORS

Your boiler is equipped with a large LCD display that indicates 

the appliance operating status. 

1. THINGS YOU SHOULD KNOW

  

Unica i28

Unica i32

Unica i36

HEIGHT

780 mm

780 mm

780 mm

WIDTH

400 mm

400 mm

400 mm

DEPTH

358 mm

358 mm

384 mm

ABOVE

150 mm

BELOW

150 mm

LEFT SIDE

12 mm

RIGHT SIDE 12 mm
FRONT

600 mm

Содержание Unica i28













































Отзывы: