5. PROGRAMMING
D-304762 PowerMaster-10/30 G2 Installer's Guide
49
Option
Configuration Instructions
Enter the "1
st
RPRT CHAN"; option and define which of the communication channels the
system will use as the main reporting channel. To define also backup reporting channels,
enter the "2nd RPRT CHAN" and "3rd RPRT CHAN" options and define them as well.
Options:
disable
(default);
cellular
and
PSTN
.
Important:
Only selected communication channels will be used by the system to report event
messages to Monitoring Stations.
If none is selected, the reporting to
monitoring stations will be disabled
.
Note:
When
Cellular
channel is selected, the order of priority will be GPRS (IP)
channel first, then GSM voice channel and lastly SMS channel, provided that
these channels have been enabled in section 5.6.3.
05:DUAL REPORT
Define whether or not to report events using
PSTN and Cellular
.
Options:
disable
(default) and
PSTN & cellular
.
11:RCVR1 ACCOUNT
12:RCVR2 ACCOUNT
Enter the respective 1
st
Account (subscriber) number (11:RCVR 1 ACCOUNT) that will
identify your specific alarm system to the 1
st
Monitoring Station (designated as RCVR1 or
RCV1) and a 2
nd
Account (subscriber) number (12:RCVR 2 ACCOUNT) that will identify the
system to the 2
nd
Monitoring Station (designated as RCVR2 or RCV2). Each of the Account
numbers consists of 6 hexadecimal digits.
Master Installer only
To enter Hexadecimal digits, use the following table:
Entering Hexadecimal Digits
Digit
0…..9
A
B
C
D
E
F
Keying
0…..9
[#]
[0]
[#]
[1]
[#]
[2]
[#]
[3]
[#]
[4]
[#]
[5]
16:PSTN/GSM RCV1
17:PSTN/GSM RCV2
Master Installer only
The PowerMaster can be programmed to report the event messages defined in the Report
Events option (option 01) to two Alarm Format Receivers via PSTN telephone line and/or
GSM analog voice channel (if equipped with GSM module), using standard PSTN alarm
formats (i.e. SIA and/or Contact-ID approved by UL, and Scancom not for UL). The reporting
format is defined in the "PSTN Report Format" option (option 41).
Enter the two respective telephone numbers (
including area code
– maximum 16 digits) of
the Alarm Format Receiver 1 located at the 1
st
Monitoring Station (16: PSTN/GSM RCV1)
and alarm format Receiver 2 located at the 2
nd
Monitoring Station (17: PSTN/GSM RCV2).
Note:
If any of the phone numbers programmed herein contain an
area code
identical to the
area code of the PSTN telephone line to which the system is connected, you should refer to
the "
AREA CODE
" option in section 5.6.2.and act as instructed there.
Digit
Keying
Digit Significance
A
[#]
[0]
The dialer waits 10 seconds or waits for dial tone, whichever comes first
and then dials. Applicable only at the 1
st
digit.
D
[#]
[3]
The dialer waits 5 seconds for dial tone and goes on hook if none is
received. Applicable only at the 1
st
digit.
E
[#]
[4]
The dialer waits 5 seconds. Applicable only in the middle of the number.
To
move the cursor
and
clear digits
, use the
"String Editor's"
keys as described in the
table at the end of section 5.6.3.
21:IP RCVR 1
22:IP RCVR 2
Master Installer only
If equipped with GSM or Broadband/PowerLink modules, the PowerMaster can be programmed
to report the event messages defined in Report Events option (option 01) to two IP Receivers,
Visonic PowerManage model. IP reporting can be performed via GPRS (IP) channel using SIA
IP format or via Broadband IP channel using SIA IP or Visonic PowerNet format.
Enter the two IP addresses (000.000.000.000) of the IP Receiver 1 located at the 1
st
Monitoring
Station (21:IP RCVR 1) and IP Receiver 2 located at the 2
nd
Monitoring Station (22:IP RCVR 2).
26:SMS RCVR 1
27:SMS RCVR 2
Master Installer only
If equipped with GSM module, the PowerMaster can be programmed to report the event
messages defined in Report Events option (option 01) to two SMS Receivers via the GSM
SMS channel using a special SMS text format. For further details concerning the SMS text
format please contact Visonic.
