Rev. 2.0 - EN EU - fw 5.22
32
2. env+ = envelope positive
mode
(for example, touch wah). In this config-
uration, the filter will move according to the settings of page 5/6, and the
filter frequency shift will
increase
proportionally to the playing strength.
For more detail, see page
5/6
of the Filter configuration menu.
3. env- = envelope negative mode
. In this configuration, the Filter will move
according to the settings of page 5/6 and the filter frequency shift will
decrease
proportionally to the playing strength. For more detail, see
page
5/6
of the Filter configuration menu.
4. manual = manual mode
(for example, Crybaby, Vox)
or
fixed mode
. See
page
6/6
for the settings of this page.
•
To change the Filter Mode settings of F1 (F1Md) or F2 (F2Md), press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position the blinking cursor next to F1Md or
F2Md. Adjust the value with the
selection dial
[
4
].
QUICK TIP - Wah:
If you set
F1Md
to env+ , the filter F1 will produce the
sound of an envelope wah (touch wah).
PAGE 3/6 - AUTO MODE MODULATION SETTINGS FOR F1
This page is used to configure filter F1 when auto mode is selected for F1
(
F1Md
set to auto on page
2/6
).
Tempo: 07 .
Ph:
0
0
0
Ì
6 4
È3/6
W v
a
i n
e
:
1 s
e
F i n
m
[ Hz
0
:
1
]
0
7
4
F ax
m
[ Hz
0
:
1
]
0
9
8
F
WaveF1
– Filter F1 modulating waveform. Range: sine, trig, trap, rect, expo,
shl1, shl2, shl3.
This parameter selects the waveform assigned to the individual modulator of
each filter. You can choose from among the following possibilities (see ‘
Ap-
pendix A
’ on page 62 for more details on the modulating waveforms):
1. sine
= sinusoidal
2. trig
= triangle
3. trap
= trapezoidal
4. rect
= symmetric square waveform
5. expo
= exponential
6. shl1
= shelf waveform 1
7. shl2
= shelf waveform 2
8. shl3
= shelf waveform 3
•
To change or select a modulating waveform for F1, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position the blinking cursor next to WaveF1. Adjust the
value with the
selection dial
[
4
].
Tempo
– Speed of the F1 modulator. Range 3 BPM (20 s) - 550 BPM (9.16 Hz)
•
To change the Tempo of the F1 modulating waveform, press
EDIT
[
5
]. Use
the
arrow keys
[
3
] to position the blinking cursor next to Temp. Adjust the
value with the
selection dial
[
4
].
Ph
– Phase of the F1 modulator. Range: 0°, 90°, 180°, 270°
Parameter Ph controls the phase of the modulating waveform. It is used to
control the relative phase of effects such as the Tremolo/Panner, Phaser, Fil-
ters (in auto mode), and Chorus, when used simultaneously. (For more details
refer to the QUICK TIP box ‘
Phase of the modulating waveforms
’, on page 25).
•
To alter the phase of the F1 modulator, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position the blinking cursor next to Ph. Adjust the value with the
selection dial
[
4
].
Fmin1[Hz]
– F1 minimum frequency. Range: 370 Hz to 1968 Hz
Fmax1[Hz]
– F1 maximum frequency. Range: 370 Hz to 1968 Hz
These values define the frequency range swept by filter F1 in auto mode.
•
To change the value of Fmin1 or Fmax1, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position the blinking cursor next to Fmin1 or Fmax1. Adjust the value
with the
selection dial
[
4
].
Please note: PedalPro will NOT allow you to set Fmax1 smaller than
Fmin1.
9
Working with Effects: Filters
Содержание PedalPro
Страница 59: ...59 Rev 2 0 EN EU fw 5 22 13 Technical Specs ...
