Rev. 2.0 - EN EU - fw 5.22
26
9
9.3.6 Phaser
A phaser is an effect that uses a comb-like filter to create a series of notches
in its frequency response. These are then usually time-modulated or swept
across a range of frequencies.
The Phaser in the PedalPro is implemented using six custom-made optical
resistors and produces a sound just like the shimmering tones typical of the
70’s (and similar to the Morley Pro-Phaser*).
But the PedalPro Phaser outperforms any classic vintage equivalent. Pedal-
Pro uses six OP275 operational amplifiers that allow for a far greater transpar-
ency, an ultra-low noise output, and an incredible modulator flexibility.
The phase and the Phaser’s modulating waveforms
is completely under your
control
, and can be synchronised with any other phase-controlled effect.
PARAMETERS
•
To enter the Phaser configuration page, press the
multifunction key
[
10a
]
labelled ‘
Phasr
’ on
page 2
of the main menu.
The screenshot below shows you the screen of the Phaser configuration
page:
È1 /1
P a
h s r
a
M
ua
n
Ç Á
l
:
D pt
e
: 06
2
.
s
Tempo : 07 .
Ph :
0
9
0
Ì
h
i n
6
Wv
e
2 0
e
: 01 .
2 1
Phaser
– Phaser effect switch. Range: on (
Á
), off (
Â
)
•
To add (
Á
) or remove (
Â
) the analogue Phaser from your effect chain,
press the
BYPASS EFFECT 1
key [
10a
].
Manual
– Manual phase shift selection. Range: 0-100%
When you set the
Depth
parameter (see below) to 0, the amount of phase
shift then depends on the level assigned to the
Manual
parameter.
•
To change the amount of manual phase shift to the signal, press
EDIT
[
5
],
and use the
arrow keys
[
3
] to position the blinking cursor next to Manual.
Adjust the value with the
selection dial
[
4
].
Tempo
– Speed of the modulator. Range 3 BPM (20 s) - 550 BPM (9.16 Hz)
•
To change the Tempo of the modulating waveform, press
EDIT
[
5
], and
use the
arrow keys
[
3
] to position the blinking cursor next to Tempo. Ad-
just the value with the
selection dial
[
4
].
Wv
– Modulating waveform. Range: sine, trig, trap, rect, pcal, shlf, vntg
The Phaser has many modulating waveforms from which you can choose. All
the classic waveforms are included, along with some exclusive VR-designed
waveforms. Available waveforms include: sine, triangle, trapeze, rectangle,
pcal (phaser calibrated curve, linear phase sweep), shlf (shelf), vntg (vin-
tage). (see
Appendix A
for more details on the modulating waves).
•
To change or select a modulating waveform, press
EDIT
[
5
], and use the
arrow keys
[
3
] to position the blinking cursor next to Wv. Adjust the value
with the
selection dial
[
4
].
Depth
– Depth of the modulation. Range: 0-100%
The depth parameter controls the depth of the phaser effect.
•
To alter the depth of the Tremolo or Panner effect, press
EDIT
[
5
], and use
the
arrow keys
[
3
] to position the blinking cursor next to Depth. Adjust the
value with the
selection dial
[
4
].
Ph
– Phase of the modulator
.
Range: 0°, 90°, 180°, 270°
The phase of the modulator controls the phase of the modulating waveform.
It is used to control the relative phase among effects that offer the possibility
of selecting the Phase of the Modulator (Ph), e.g., Tremolo/Panner, Phaser,
Auto Filters, Chorus. (For more details refer to the QUICK TIP box ‘
Phase of the
modulating waveforms
’, on page 25).
•
To alter the phase of the Tremolo or Panner effect, press
EDIT
[
5
], and use
the
arrow keys
[
3
] to position the blinking cursor next to Ph. Adjust the
value with the
selection dial
[
4
].
*All trademarks are property of their respective owners and used for reference only.
Working with Effects: Phaser
Содержание PedalPro
Страница 59: ...59 Rev 2 0 EN EU fw 5 22 13 Technical Specs ...
