Viessmann Vitocal 242-S Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 152

background image

74

G

Fill hose between pressure gauge
set and external unit

H

Pressure gauge set

K

Connection hose between pressure
gauge set and vacuum pump

L

Vacuum pump

M

Connection hose between pressure
gauge set and vacuum gauge

N

Valve for vacuum gauge

O

Vacuum gauge

!

Please note

Never subject the vacuum
gauge
to positive pressure.

1.

Close all valves at the pressure
gauge set.

2.

Make all connections, as shown
above.

!

Please note

Filler valve

D

must

remain

closed.

Finally

, connect the end of

the filling hose to the service
valve

E

.

For

all

connections, counter-

hold with a second open-
ended spanner.

3.

Start the vacuum pump.
At the pressure gauge set, open the
valve to the vacuum pump and the
valve to the hot gas connection.

4.

After approx. 5 min, open the valve to
the vacuum gauge.
Leave the vacuum pump running until
almost 0 bar is indicated on the vac-
uum gauge (at least 30 min).

Note
The vacuum pump runtime will
depend on the ambient conditions.

5.

Close the valve on the pressure
gauge set to the vacuum pump.
Stop the vacuum pump and wait
approx. 5 min. There is a leak if the
indication on the vacuum gauge
rises.
Remove the leak and repeat the proc-
ess.

6.

Close all valves at the pressure
gauge set.

7.

Remove the vacuum pump and vac-
uum gauge.

Commissioning, inspection, maintenance

Further details regarding the individual steps

(cont.)

5623 661 GB

«
...
72
73
74
75
76
...
»

Содержание Vitocal 242-S

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vitocal 242-S

Бренд: wallas Страницы: 40

Бренд: Makita Страницы: 96

Бренд: Samoa Страницы: 32

Бренд: Gamo Страницы: 25

Бренд: Gamma Vacuum Страницы: 27

Бренд: iGenix Страницы: 6

Бренд: Qlima Страницы: 14

Бренд: York Страницы: 90

Бренд: Clarke Страницы: 16

Бренд: Mylek Страницы: 8

Бренд: Dometic Страницы: 10

Gas Log Grate Heater

Бренд: Stoll Страницы: 4

Mini-CHIEMSEE B 1100

Бренд: SHG Страницы: 26

BREDEL 701 Series

Бренд: Watson-Marlow Страницы: 25

Бренд: BIEMMEDUE Страницы: 28

CENTRI PUPPY 18510-000 Series

Бренд: JABSCO Страницы: 4

Бренд: Dru Страницы: 56

ULTRA-FLO MY3-50 METAL Series

Бренд: Q-MAX Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды