Viessmann Vitocal 242-S Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 152

background image

2

Please follow these safety instructions closely to prevent accidents and mate-
rial losses.

Safety instructions explained

Danger

This symbol warns against the
risk of injury.

!

Please note

This symbol warns against the
risk of material losses and envi-
ronmental pollution.

Note
Details identified by the word "Note" con-
tain additional information.

Target group

These instructions are exclusively inten-
ded for qualified contractors.
■ Work on the refrigerant circuit may

only be carried out by authorised
refrigeration engineers.

■ Work on electrical equipment must

only be carried out by a qualified elec-
trician.

■ The system must be commissioned by

the system installer or a qualified per-
son authorised by the installer.

Regulations

Observe the following when working on
this system:
■ National installation regulations
■ Statutory regulations regarding the

prevention of accidents

■ Statutory regulations regarding envi-

ronmental protection

■ Codes of practice of the relevant trade

associations.

■ All current safety regulations as

defined by DIN, EN, DVGW, VDE and
all locally applicable standards

a

ÖNORM, EN and ÖVE

c

SEV, SUVA, SVTI, SWKI and
SVGW

Working on the system

■ Isolate the system from the power sup-

ply (e.g. by removing the separate fuse
or by means of a mains isolator) and
check that it is no longer 'live'.

Note
In addition to the control circuit, there
may be several power circuits.

Danger

Contact with 'live' components
can result in severe injuries.
Some components on the
PCBs will remain 'live' even
after the power supply has
been switched off.
Prior to removing equipment
covers, wait at least 4 min. to
allow the voltage to dissipate.

■ Safeguard the system against recon-

nection.

Safety instructions

Safety instructions

5623 661 GB

«
1
2
3
4
...
»

Содержание Vitocal 242-S

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vitocal 242-S

Бренд: iBath Страницы: 12

TOPAZ Direct Vent Room Heater 839-1290

Бренд: Quadra-Fire Страницы: 56

Бренд: Easy@Home Страницы: 42

Бренд: Edwards Страницы: 16

Бренд: Ozito Страницы: 6

Бренд: Mannesmann Страницы: 3

Desk Friend DDF250

Бренд: Dimplex Страницы: 4

Бренд: VONROC Страницы: 60

Бренд: Graco Страницы: 20

Бренд: Watts Страницы: 22

Бренд: Graco Страницы: 32

REMINGTON REM-16-TTC-O

Бренд: Pinnacle Climate Technologies Страницы: 32

Бренд: True North Страницы: 20

Бренд: VOLTOMAT HEATING Страницы: 104

Бренд: Daikin Страницы: 44

Бренд: YAMADA Страницы: 25

FLOJET G55 Series

Бренд: Xylem Страницы: 2

Бренд: Rinnai Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды