Viessmann B23 Скачать руководство пользователя страница 55

Страница: 55 / 108

All coding addresses in the table are listed in the "General" group.
Boiler control unit

Vitotronic 200-H

Vitocom

LON

Subscriber no. 1
Code "77:1"

Subscriber no. 10
Code "77:10"

Subscriber no. 11

Set

code "77:11".

Subscriber no. 99

Control unit is fault manager.
Code "79:1"

Control unit is not fault man-
ager.
Code "79:0"

Device is fault man-
ager.

Control unit transmits the
time.
Code "7b:1"

Control unit receives the
time.

Set

code "81:3".

Control unit receives the
time.

Set

code "81:3".

Device receives the
time.

Control unit sends outside
temperature.

Set

code "97:2".

Control unit receives outside
temperature.

Set

code "97:1".

Control unit receives outside
temperature.

Set

code "97:1".

—

Viessmann system number.
Code "98:1"

—

LON subscriber fault monitor-
ing.
Code "9C:20"

LON subscriber fault moni-
toring.
Code "9C:20"

—

Carrying out a LON subscriber check

The subscriber check is used to test communication
with the system devices connected to the fault man-
ager.

Requirements:

■

The control unit must be programmed as

fault man-

ager

(code "79:1" in the

"General"

group).

■

The LON subscriber number must be programmed in
all control units.

■

The LON subscriber list in the fault manager must be
up to date.

Service menu:

Press

and

simultaneously for approx. 4 s.

2. "Service functions"

3. "Subscriber check"

Select subscriber (e.g. subscriber 10).

Start the subscriber check with

"OK"

■

Successfully tested subscribers are designated with

"OK"

■

Unsuccessfully tested subscribers are identified with

"Not OK"

Note

To perform another subscriber check:
Create a new subscriber list with

"Delete list?"

(sub-

scriber list is updated).

Note

During the subscriber check, the display of the relevant
subscriber shows the subscriber no. and

"Wink"

for

approx. 1 min.

Commissioning, inspection, maintenance

Linking the control unit to the LON

(cont.)

6136330

Содержание B23













































































































Результаты поиска

Содержание B23

Отзывы:

Похожие инструкции для B23

Бренды по названию

Популярные бренды

Viessmann B23, Инструкция по установке и обслуживанию

Результаты поиска

Содержание B23

Отзывы:

Похожие инструкции для B23

Бренды по названию

Популярные бренды