Vicon SVFT-C22, Инструкция по установке и эксплуатации

Страница: 62 / 80

54
•
9BCompetitive Protocols XX134-07-00 Rev 908 SurveyorVFT Camera Dome System
Pelco
Function Keypress Function Keypress
s),
Program Sectors
96, Preset Set (Program Label screen appears),
F2 then press Pan Auto to set sectors, Aux 2 and
3 to set mask.
97, Preset Set (Program Label screen appears),
92, Preset Set (Program Label screen appears),
o
),
o
agnostic Screen
s),
F2
s),
s
nter
e
t
ill
ss
ter
n
also
Turbo (Set speed to
ngage. Press <1> , F3 to disengage Feature) Not Supported
Presets Preset Recall - Enter Preset Number, Preset Go V-Phase Menu system
Pan and Tilt Lockout
94, Preset Set (Program Label screen appears),
F2. Repeat to unlock.
Enter Menu
95, Preset Set (Program Label screen appears),
F2 Set
Transmit Polarity
93, Preset Set (Program Label screen appear
F2
Select/Store IO (Iris Open)
Backup/Abort/Exit IC (Iris Close) Reset Dome F2
Iris Open Iris Open- Controls Autoiris Levels Set AP limits
F2 then <2> Aux to set left limit and <3> Aux t
set right limit
Iris Close Iris Close - Controls Autoiris Levels Set Pan limits
90, Preset Set (Program Label screen appears
F2 then <2> Aux to set left limit and <3> Aux t
set right limit
Focus Near
Focus Near
Di
91, Preset Set (Program Label screen appear
Focus Far
Focus Far
Debug Screen
99, Preset Set (Program Label screen appear
F2
The controller MPT9500 doesn't support Pelco
tours. Vicon's tours are accessible using preset
80-87 or the menu system. To store a tour, E
Zoom Out
Zoom Wide
Preset Tours
preset number, Preset Set , F2. To run tour us
Preset Go.
Pelco calls these patterns; there are multiple
ways of programming. The keypad has defaul
Zoom In Zoom Tele Auto Tour
press Aux 1 again to stop programming. The
press IO to store or IC to abort. The tour can
be programmed thru the menu system.
Camera Off
Camera Off
Night Mode- Manual <6> Aux to engage. <6> F3 to disengage
Camera On
Camera On
Alarms Programmed through the menu system.
Autopan Pan Auto = On , Pan Man = Off Alarm Acknowledge
Enter any number from 1-9 and press "Alarm
Ack". The SurveyorVFT will acknowlede the
alarms in received order.
shortcut keys. This maps to our preset 88. It w
not access preset 89. Press <1>, F1 to start
programming. Press <2>, F1 to stop
programming. Press <3>, F1 to run the tour.
Programming using the Vicon way allows acce
to autotours 88 and 89. To program tour 88 en
<88>, Preset Set, F2 to start programming. A
prompt appears to press Aux 1 to start
programming. When the pattern is complete
Autoiris No Control- Unit is always in autoiris. full) - (Pelco Feature) Turbo Button
Lens Speed
8, F1, enter 1 or 2 for low, 3 for med , 4 for high.
Zoom and focus speed are the same.
Flip (Turn 180 degrees) 5,F1
Auxs
Supports only a latching relay. Press <1>, Aux
to e Peel (Sensormatic
Preset Store - 1 to 32 , 35 to 79 - Enter Preset
Number, Preset Set (Program Label screen
appears), F2 - No preset label editing. Can be
programmed through menu.
Camera Control
Including Adjust