manualshive.com logo in svg

Vicon surveyor 2000 XX004, Инструкция по установке и эксплуатации


Поделиться
Скачать
background image

XX004 Rev 500 Surveyor2000 Pressurized Housing Camera Dome

Contents  

••••

  i

Contents

INTRODUCTION .................................................................................................................. 1

How to Use this Manual ................................................................................................................................ 1

Accessory Kit ................................................................................................................................................. 1

Unpacking and Inspection ............................................................................................................................ 1

Pressurized Housing Components .............................................................................................................. 2

Housing..................................................................................................................................................... 2
Camera Drive............................................................................................................................................ 2
Trim Ring/Lower Dome Assembly ............................................................................................................ 2

INSTALLATION ................................................................................................................... 3

Wall Mount Method........................................................................................................................................ 3

Installing the Wall Mount........................................................................................................................... 3
Installing the Camera Dome ..................................................................................................................... 4
Pressurizing the Housing Assembly ......................................................................................................... 6
Installing the 23-pin Connector Assembly ................................................................................................ 7
Wiring and Assembling the 23-pin Connector .......................................................................................... 8
Final Assembly.......................................................................................................................................... 9

Pipe Mount Method...................................................................................................................................... 10

Installing the Pipe Mount......................................................................................................................... 10
Installing the Camera Dome ................................................................................................................... 11
Pressurizing the Housing Assembly ....................................................................................................... 13
Installing the 23-pin Connector Assembly .............................................................................................. 14
Wiring and Assembling the 23-pin Connector ........................................................................................ 15
Final Assembly........................................................................................................................................ 16

MAINTENANCE ................................................................................................................. 17

Care and Cleaning of Clear Acrylic Domes ............................................................................................... 17

Fuse Replacement ....................................................................................................................................... 17

SHIPPING INSTRUCTIONS .............................................................................................. 19

REFERENCE ..................................................................................................................... 21

Coaxial Cable ............................................................................................................................................... 21

Twisted-Pair Cable....................................................................................................................................... 22

1.5-inch (38 mm), Schedule 40 Pipe Designation ..................................................................................... 22

TECHNICAL INFORMATION............................................................................................. 23

Содержание surveyor 2000 XX004





































Отзывы:

Нет отзывов

Похожие инструкции для surveyor 2000 XX004

Barnett Engineering ProTalk Cv3 Replacement Instructions preview
ProTalk Cv3
Бренд: Barnett Engineering Страницы: 3
Speco SIPB1 Instruction Manual preview
SIPB1
Бренд: Speco Страницы: 104
Perel CCTVSET2 User Manual preview
CCTVSET2
Бренд: Perel Страницы: 20
Conbrov WF91 User Manual preview
WF91
Бренд: Conbrov Страницы: 36
Eneo EDMC-142 Installation And Operating Instructions Manual preview
EDMC-142
Бренд: Eneo Страницы: 90
D-MAX DCC-500F User Manual preview
DCC-500F
Бренд: D-MAX Страницы: 22
Abus CO alarm User Manual preview
CO alarm
Бренд: Abus Страницы: 220
TRIVIEW TFD-S36FI12IR Operating Instructions preview
TFD-S36FI12IR
Бренд: TRIVIEW Страницы: 5
Isonas powernet Manual preview
powernet
Бренд: Isonas Страницы: 48
DBI SALA FSHRS Operator'S Manual preview
FSHRS
Бренд: DBI SALA Страницы: 28
FujiFilm XF10-24mmF4 R OIS Owner'S Manual preview
XF10-24mmF4 R OIS
Бренд: FujiFilm Страницы: 136
T'nB SHCAMHD User Manual preview
SHCAMHD
Бренд: T'nB Страницы: 21
Lupus LUPUSNIGHT-139HD User Manual preview
LUPUSNIGHT-139HD
Бренд: Lupus Страницы: 11
Ningbo DSW PS-372 Installation Manual preview
DSW PS-372
Бренд: Ningbo Страницы: 2
Foxtech Bi-Focus User Manual preview
Bi-Focus
Бренд: Foxtech Страницы: 25
Hanwha Vision PNM-C16083RVQ Quick Manual preview
PNM-C16083RVQ
Бренд: Hanwha Vision Страницы: 22
Polaroid PL126-PZ User Manual preview
PL126-PZ
Бренд: Polaroid Страницы: 1
DSE RE-BCC8FD Owner'S Manual preview
RE-BCC8FD
Бренд: DSE Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды