Viavi 87339 Скачать руководство пользователя страница 47

Страница: 47 / 198

Testing

3 - 6

Control Component

Description

SBAS

Drop Down Selections:

AUTO - Automatic optimized selection of SBAS satellite

(WAAS/EGNOS) according to simulated position.

OFF - SBAS satellites are turned OFF.

NOTE:

With AUTO selected only 5 or 11 GPS/Galileo SV’s are

available. With OFF selected a full 6 or 12 GPS/Galileo SV’s

are available.

NOTE:

Actual Number of available SV’s is dependent on user

options.

NOTE:

Locations without SBAS satellite coverage will result in

no SBAS signals being generated in some simulations, even

though SBAS SV simulation has been enabled.

NOTE:

According to the NMEA specification, the numbers

33 to 64 are reserved for SBAS satellites. The offset from

NMEA SBAS SV ID to SBAS PRN is 87. For example, an SBAS

PRN number of 138 minus 87 results in an SV ID of 51. From

the preceding example, some receivers will report the ID of the

SV as 138, while some receivers may report the ID as 51.

Digital Noise

Drop Down Selections:

Off - When coupling to the receiver antenna.

On - When connecting directly to the receiver, bypassing the

antenna/LNA.

NOTE:

Automatically set to OFF when RF PORT = COUPLER.

Automatically set to ON when RF PORT = DIRECT.

NOTE:

Use of digital noise via antenna coupler will result in

degraded SV Signal to Noise ratio and may cause receiver to

loose track or not obtain a stable fix.

Fading

Drop Down Selections:

None - SV signal amplitudes do not have fading applied.

Static - SV signal amplitudes have amplitude fading applied.

Pedestrian - SV signal amplitudes have amplitude fading

applied.

Land Vehicle - SV signal amplitudes have amplitude fading

applied.

Aircraft - SV signal amplitudes have amplitude fading applied.

NOTE:

None, Pedestrian, Land Vehicle and Aircraft amplitude

fading are recommended for use in Dynamic mode. None and

Static are recommended for use in Static mode.

NOTE:

See section 3.2.2.A for additional information on

Fading and multi-path Implementation.

PRN Signal

Drop Down Selections:

Fixed - All SV Levels are set to the amplitude selected in the

RF Level control component.

Variable - Ensures the relative SV signal levels are set

proportional to the respective pseudo ranges.

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды