Viavi 87339 Скачать руководство пользователя страница 100

Страница: 100 / 198

5 -1

Chapter 5 - Maintenance

5.1

INTRODUCTION

5.1.1

Visual Inspections

Visual inspections should be performed periodically depending on operating environment,

maintenance and use.

5.1.2

External Cleaning

STEP

PROCEDURE

Clean front panel buttons and display face with soft lint-free cloth. If dirt is

difficult to remove, dampen cloth with water and a mild liquid detergent.

Remove grease, fungus and ground-in dirt from surfaces with soft lint-free cloth

dampened (not soaked) with isopropyl alcohol.

Remove dust and dirt from connectors with soft-bristled brush.

Cover connectors, not in use, with suitable dust cover to prevent tarnishing of

connector contacts.

Clean cables with soft lint-free cloth.

Paint exposed metal surface to avoid corrosion.

5.2

MAINTENANCE PROCEDURES

5.2.1

Battery Replacement

Perform the following steps to replace battery:

STEP

PROCEDURE

Verify the GPSG-1000 is OFF and not connected to AC power via the AC Adapter.

Place the GPSG-1000 on a flat surface, lower side up.

Lift the battery cover Pull Tab to a vertical position to release the Battery Cover

and lift away from the Case Assembly.

NOTE:

Some batteries may be fitted with a sliding catch. Depress catch to

release battery. Tip the unit backwards to release the battery.

Remove the battery from the battery housing (Fig 5-1).

Install new battery in the battery housing.

Replace the battery cover on the case assembly by locating the lipped end of the

cover in the case assembly. Lift the pull tab and push the battery cover down,

ensuring the catch engages. Release the pull tab and ensure battery lays flat

inside the recess.

NOTE:

Some batteries may be fitted with a sliding catch. Depress catch to

install the battery.

DISPOSE OF OLD BATTERY ACCORDING TO LOCAL STANDARD

SAFETY PROCEDURES.

BY ELECTR

W A R N I N G

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды