Viavi 87339 Скачать руководство пользователя

Страница: 105 / 198

Testing

5 -6

5.2.5

GPSG-1000 Almanac Update

Perform the following steps to Update GPSG-1000 Almanac using a USB memory device

STEP

PROCEDURE

Obtain the current GPS almanac for the week from the United States Coast Guard

Navigation Center at

http://www.navcen.uscg.gov/?pageName=gpsAlmanacs

and

save the file as “

current.alm

” or as “

weekXYZ.alm

” with XYZ being the current

almanac week (week617.alm).

Copy the almanac file, named “

current.alm

” to the USB memory device (VIAVI

Solutions P/N 67325) under the directory name of

Instrument/almanacs/

plus

almanac file name (/Instrument/almanacs/week617.alm).

Power up the GPSG-1000.

Select

System

, then select

System Update

from the drop down menu on the

GPSG-1000.

Insert the USB memory device into USB Host 1 Port or Host Port 2.

Wait 5 to 10 seconds for the device to be recognized and then select

Copy from

USB

The Almanac file will be copied to the GPSG-1000.

The status message should read ‘Upgrade Done’.

Remove the USB memory device.

10.

Proceed to

Setup

window, then press

Almanac Source

. Press

File

, then select

the newly loaded almanac file to load.

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды