Viavi 87339 Скачать руководство пользователя

Страница: 112 / 198

Testing

5 -13

Display Component

Description

Slot 1 MIC284

Temperature

Displays the current PXI slot 1 controller MIC284 temperature

in degrees Celsius.

Slot 1 OMAP

Temperature

Displays the current PXI slot 1 controller OMAP processor

temperature in degrees Celsius.

Digital Board

Temperature

Displays the current PXI digital board temperature in degrees

Celsius.

Control Component

Description

Format SD

Formats the internal SD memory card overwriting all stored

data.

NOTE:

The user will be prompted YES or NO prior to execution

of formatting.

Caution:

Formatting will result in complete irretrievable loss

of almanac, route, setting, Nmea, Kml, and waypoint data

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды