Viavi 87339 Скачать руководство пользователя страница 48

Страница: 48 / 198

Testing

3 - 7

Control Component

Description

Position Source

Drop Down Selections:

User - User entered position.

GPS - On board GPS receiver derived position.

Clock

Drop down selections:

GPSRX - simulation uses uncorrected GPS UTC time and date

in conjunction with loaded almanac and ephemeris data.

USER- simulation uses User entered Time and Date which

sets SV parameters against loaded almanac and ephemeris.

INTERNAL - simulation uses time and date that is available

from the real time clock of the GPSG-1000.

Date

Incremental Data Entry: Date to be used during simulation.

Time

Incremental Data Entry: Time to be used during simulation.

NOTE:

The appropriate message content announcing a future

leap second event is transmitted when simulation dates are

within a period starting approximately 60 days before the leap

second event. The appropriate message content is updated

within two hours after the leap second event.

RF Level

Numeric Pad: RF level entered as -68 to -130 dBm in Coupler

mode or -93 to -155 dBm in Direct mode.

NOTE:

The listed RF Level settings are assuming 0 dBm

settings for Coupler Loss, Coupler Cable and Direct Cable on

the Setup I/O Window. The RF Level entry window will be

reduced by the values entered for these settings.

RF Port

Drop Down Selections:

Direct - Generator uses GPS TX DIRECT port.

Coupler - Generator uses GPS TX COUPLER port.

Units

Drop Down Selections:

Imperial - Parameters displayed/entered in Imperial units.

SI - Parameters displayed/entered in SI units.

Aero/Imperial - Parameters displayed/entered in Imperial

units, speed is display/entered in knots.

Aero/SI - Parameters displayed/entered in SI units, speed is

displayed/entered in knots.

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды