Viavi 87339 Скачать руководство пользователя страница 84

Страница: 84 / 198

Testing

4 -3

STEP

PROCEDURE

Perform the following steps to complete Simulation:

PVT:

Latitude = For Optional entry of test Latitude
Longitude = For Optional entry of test Longitude
Altitude = For Optional entry of test Altitude

10.

Select

RUN

key to start simulation.

11.

Select STOP key to discontinue simulation.

NOTE:

Most GPS receivers expect ACTIVE antennas, this means they supply a DC

voltage to the antenna connector. The GPSG-1000 has built in DC voltage

blocking on the GPSG

1000 TX Port.

NOTE:

Some receivers “sense” current draw on the DC supply to their active antenna.

If there is no current drawn, they may assume that no antenna is connected. In

such cases, the current draw must be simulated by some resistive load and

perhaps a series inductor between the signal line and the ground. Such a device

may need to be custom built, depending on the receiver requirements.

NOTE:

It is recommended that the receiver under test is “cold started” and a fresh

almanac obtained from the GPSG-1000 simulation. This process may take several

minutes, dependent on specific receiver.

NOTE:

Some receivers will not obtain a stable fix when using a simulation time earlier

than the selected almanac. Generally it is best to utilize an almanac that is dated

at least one day before the simulation date.

NOTE:

NOTE: It is important that the receiver under test is not able to receive signals

from the real GPS constellation as the pseudo-ephemeris data of the simulation is

different enough from the real constellation that the mix of data can cause

problems with the receivers positional calculation.

GPS TX PORT: APPLIED DC SHOULD NOT 50 V

C A U T I O N

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Бренды по названию

Популярные бренды