Viavi 87339 Скачать руководство пользователя страница 29

Страница: 29 / 198

2 - 1

Chapter 2 - Test Set Operation

2.1

INTRODUCTION

This chapter refers to local operation of a GPSG-1000 configured with factory default

settings unless specified otherwise. New Test Sets are configured to start in the factory

default setting. Review Installation and Power Requirements before using the Test Set.

2.2

POWER REQUIREMENTS

2.2.1

Power

The GPSG-1000 is powered by an internal Lithium Ion Battery. The battery charging

circuit enables the operator to recharge the battery anytime the unit is connected to the

DC power supply. The GPSG-1000 can operate continuously utilizing the DC power

supply. The internal battery is equipped to power the GPSG-1000 for four hours of

continuous use.

2.2.2

AC Power Requirements

The DC Power Supply supplied with the GPSG-1000 operates over a voltage range of

100 to 250 VAC at 47 to 63 Hz. The battery charger operates whenever DC Power

(11 to 32 Vdc) is applied to the Test Set with the supplied DC Power Supply or a suitable

DC power source.

NOTE: I

f the supply voltage is <11V, the unit will switch to internal battery. If the voltage

is >32V, a 7 AMP resettable fuse on the DC input port will open, protecting the Test Set.

When charging, the battery reaches a 100% charge in approximately four hours. The

Battery Charge temperature range is >-10° to <60°C, controlled by an internal battery

charger.

Содержание 87339







































































































































































































Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды

Viavi 87339, Руководство по эксплуатации

Результаты поиска

Содержание 87339

Отзывы:

Похожие инструкции для 87339

Бренды по названию

Популярные бренды