manualshive.com logo in svg

Viavi 87339, Руководство по эксплуатации

Поделиться
Скачать
Viavi 87339 Скачать руководство пользователя страница 118

6 -1

Chapter 6 - Principles of Operation

6.1

PRINCIPLES OF OPERATION

6.1.1

GPSG-1000

6.1.1.A

Satellite Simulation

The orbit parameters for each satellite are configurable in terms of the standard 

Keplerian (almanac) elements. The almanac used for simulation may selected from a list, 

maintained by a file management system. The files may obtained from the built in GPS 

receiver, as a current almanac load or may be loaded from a USB flash drive in 

Yuma .alm format.
The standard Keplerian elements (almanac) are used to calculate the enhanced Keplerian 

Elements (ephemeris), which are in turn used to generate the satellite motion, and are 

broadcast as part of the navigation message.
As almanac data is typically valid for several days, the GPSG-1000 does not update the 

standard Keplerian (almanac) elements during the course of the simulation.
The GPSG-1000 computes the enhanced Keplerian (ephemeris) elements by 

extrapolation of the configured standard Keplerian (almanac) elements. Any enhanced 

Keplerian elements not included in the standard Keplerian elements are set to zero. The 

GPSG-1000 generates updated enhanced Keplerian (ephemeris) elements at a fixed time 

interval of 4 hours, this being the update rate supported by both GPS and Galileo.The 

GPSG-1000 generates in real time the positions of all simulated Satellites i.e. positions 

are not be pre-computed for the entire simulation run.

6.1.1.B

Satellite Selection

For each simulated GNSS system the GPSG-1000 will perform an independent satellite 

selection process and if the total number of visible satellites exceeds the maximum 

number of hardware channels allocated to that system, then the GPSG-1000 will select 

those satellites which approximate the minimum DOP for that system. The GPSG-1000 

updates its satellite selection every 60 minutes.

NOTE:

In the case of the 6 channel GPSG-1000, with large numbers of simulated satellites it 

becomes possible for many more satellites to be visible at the user location than 

there are available hardware satellite channels. If this happens the GPSG-1000 

allocates channels on a 'best effort' basis but does allow the operator to override the 

selection manually.

The GPSG-1000 allows the operator to manually replace any selected satellite with 

another visible satellite from the same GNSS system, with the manually selected satellite 

remaining selected until it is no longer visible, or until it is manually replaced. The 

manually de-selected satellite will remain eligible for re-selection at the next automatic 

update.

Содержание 87339







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды