background image

Vertiv | Liebert CRV CCD10 Condenser | User Manual

 

 

 

 

Suppliers Declaration of Conformity 

 
 

 

 

Unique Identifier: 

CRD100-0D00A, CRD101-0D00A, CCD100S-00A. 

FCC Compliance Statement 

(for products subject to Part 15)

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation. 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense. 

 
 

Содержание Liebert CRV CCD10








































Отзывы: