44
20306745
VWDV70 Series Gas Fireplace
TOUCH SCREEN REMOTE CONTROL OPERATION
4. After the signal is sent, the On/up and Off/down but-
tons become
fl
ame height controller again.
5. When the light button is
fl
ashing, slide up and down on
the arrow buttons will turn the light brightness to HIGH
or Off directly without pressing the light button again to
con
fi
rm
AUX Control (Optional)
The AUX control function is used to turn on or turn off
the auxiliary component connected to the AC module of
the Signature Command System. Press the AUX button
to turn on or turn off the auxiliary.
1. When the auxiliary is turned on, the icon will
become solid text and the “ON” icon will ap-
pear below the “AUX” icon.
2. When the auxiliary is turned off, the icon will
become hollow text and the “ON” icon will dis-
appear.
NOTE:
Some
fi
replaces use the AUX function
to control options within the
fi
replace. Refer to
fi
replace
manual for operation.
Setting up Blank Screen or Constant Display in Idle
Figure 72
There is an option to set up how the LCD displays and
functions when the transmitter is in idle. There are two
choices:
1. A) Mode. When
the transmitter is
in idle, the icons
in the “touch area”
(timer, thermostat,
blower, light and
AUX) will disap-
pear, as shown in
the
fi
gure on the
left. When any of
the touch buttons
is pressed, those
icons will appear and are ready to operate (default).
2. B) Mode. The transmitter always displays all available
icons showing current status of timer, thermostat,
blower, light and AUX as shown in the
fi
gure on the
right.
Press TIMER and THERMO buttons at the same time for
3 seconds to toggle between A) and B).
1. When the current setting is A), touch any place in the
touch area to bring up the icons then press TIMER but-
ton and THERMO button at the same time for 3 sec-
onds. The backlight will
fl
ash once to indicate that the
setting has changed to B).
2. When the current setting is B), pressing TIMER button
and THERMO button at the same time for 3 seconds will
switch to A) Mode. The touch area icons will disappear.
Figure 72
Safety Features
1. Low Battery Detection
When low battery condition occurs, the transmitter will
turn off the
fi
replace.
A) Battery voltage is checked every one minute.
When the battery voltage is low, the LCD dis-
plays a low battery icon which will exist in all
modes.
B) The transmitter will not operate with low bat-
tery voltage. Change the batteries before the bat-
teries become too weak for normal operations.
2. Power On Initialization
After the power-on initialization, the transmitter sends
a signal to turn off the
fi
replace.
3. Thermal Shutdown
When the ambient temperature is more than 99°F, the
transmitter will turn off the
fi
replace.
A) The LCD will display “HI”.
B) The Transmitter will not function until
the room temperature has dropped be-
low 99 degree Fahrenheit.
4. Low Temperature Condition
When the ambient temperature is less than 40 de-
grees Fahrenheit, the LCD will display
“LO”, and NO SIGNAL will be sent to
turn on the appliance.
All functions still remain the same for
both Manual Mode and Thermostat
Mode
5. Child-proof Protection
The child-proof icon will be shown when
the child-proof mode is activated by
pressing the ON button and the OFF
button at the same time for three sec-
onds.
A) Enter childproof mode by pressing and holding both
the ON button and the OFF button simultaneous-
ly for 3 seconds. The Childproof indicator will be
shown on the LCD.
B) Deactivate childproof mode by pressing and hold-
ing the ON button and the OFF button simultane-
ously for 3 seconds again. The Childproof indicator
disappears on the LCD.
C) The transmitter cannot be operated in childproof
mode.
