20306745
41
VWDV70 Series Gas Fireplace
Setting Privacy Code on Transmitter:
Figure 62
The remote transmitter privacy code is preset in facto-
ry. In the event of activation or interference from other
nearby transmissions, change the code using the follow-
ing procedures (learn function must be performed after
changing the code):
1. Press the ON/arrow button and
the TIMER button at the same
time to enter privacy code setup
mode.
2. The setup display is shown in the
fi
gure. The four digits on the top
stand for the privacy code (as the
actual DIP switches on Ambient’s
previous remotes). The default
values of the four digits will be all
“1” (ON).
3. The
fi
rst digit will be
fl
ashing upon
entering the setup mode. Push
the ON button to toggle its value
between “0” (OFF) and “1” (ON), and push the “OFF”
button to jump to the next digit. The next digit will then
start
fl
ashing and the
fi
rst one stops
fl
ashing. Set up
the four digits to your choice.
4. After setting up all the four digits, push “OFF” to
fi
nish
the process and return to the previous mode.
5. The Signature Command control board then needs to
re-learn the new setting.
Performing Learn Function
1. The RF receiver button on the control board in the
fi
re-
place must be in the on position before the learn func-
tion can begin.
Figure 63.
With the Command Center
master switch in the ON position, use paper clip to de-
press the recessed button on Control Board, one beep
for RF receiver ON or two beeps for RF receiver OFF.
2. Holding the OFF button on the Command Center while
turning on the master switch will activate the learn
function for the transmit-
ter.
3. After the above opera-
tion, two beeps will be
given and the green LED
on the Command Center
will
fl
ash for 10 seconds.
4. During the 10 seconds,
press the OFF button on
the transmitter to learn.
Another two beeps will
be given to con
fi
rm suc-
cess.
Figure 64
TOUCH SCREEN REMOTE CONTROL OPERATION
W
ARNING
Do not use two (2) or more remote control sys-
tems in the same area with the same privacy
code setting, as they will communicate with
each other. This may cause the appliances to
malfunction.
Figure 62
RF Receiver
ON/OFF
Control Board
Figure 63
Figure 64 -
Command Center
Resetting the transmitter:
If the transmitter is not working properly, reinstall the bat-
teries to reset the transmitter.
1. Pull out at least one of the batteries.
2. Press any key on the screen to discharge.
3. Wait for 10 seconds and reinstall the batteries.
Pushing and holding any key for more than 10 seconds
until the display refreshes will also reset the transmitter.
Functions and Operations
General:
The TSFSC Remote Control has four (4) operating modes:
Manual, Timer, Thermostatic and Smart Mode. The con-
trol system can be set to temperature range between 45°
F and 90° F. The blower speed and
fl
ame height can be
adjusted in the manual, timer and thermostatic mode. The
Smart Mode will automatically adjust
fl
ame height and
blower speed according to the difference between Set
and Room temperatures.
The transmitter will operate the remote receiver from 1
foot to a maximum of 30 feet. The distance is reduced
when batteries are low.
Manual Mode
Figure 65
In this mode, the TIMER button and the THERMO but-
ton will only display “TIMER” and “THERMO”, respec-
tively without showing the time and the SET temperature.
Pressing the ON/up and OFF/down buttons will change
the
fl
ame height if none of the menu buttons (TIMER,
THERMO, LIGHT, FAN, AUX) are pressed and
fl
ashing.
Battery Door
Master Switch
ON
LED
OFF
FP2650
Front Panel
Bezel Optional
