background image

32

20306745

VWDV70 Series Gas Fireplace

FINAL INSTALLATION

Large Rear Right 
Log #2

Figure 50

Medium Top Middle 
Log #3

Figure 51

5.  Place decorative colored glass supplied with 

fi

 replace. 

Page 30

 

6.  Place medium top middle log #3 across the rear logs 

by aligning the two (2) recesses on the bottom of the 
log with the key protrusions on each of the rear logs. 
The front branch of the top log may rest on top of the 
decorative colored glass. 

Figure 51

Medium Top 
Left Log #4

7.  Place the medium top left log #4 onto the left end of 

the rear left log #1 by aligning the recess with the key 
protrusion on the rear left log. 

Figure 52

Medium Top Right 
Log #5

Figure 53

8.  Place the medium top right log #5 onto the center of 

the rear right log #2 by aligning the recess with the key 
protrusion on the rear right log. 

Figure 53

Figure 52

4.  Place the large rear right log #2 by aligning the three 

(3) holes in the bottom of the log with the three (3) pins. 

Figure 50

9.  Place the small front left log #6 on top of the decorative 

glass towards the left side of the hearth. 

Figure 54

IMPORTANT:

 Do not place this log in or near the burner 

port area. To prevent sooting and poor combustion, do not 
allow the burner 

fl

 ames to contact this log.

Содержание VWDV70NTSCSB




























































Отзывы: