manualshive.com logo in svg
background image

Z206855-0B 

Page 20 of 26 

©2014 Veris Industries   USA 800.354.8556 or +1.503.598.4564  / [email protected] 04142 

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of  Veris Industries, L.L.C. in the USA and/or other countries.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Installation Guide

Power Monitoring

E31E Series

TM

The next field for the BACnet MS/TP protocol mode is the MSTP_Max_Master, which allows this value to be set prior to using 
BACnet software to access the E31E. The default value of 127 works regardless of the addresses the MS/TP network uses, but 
selecting a lower value may optimize the network. Do not set this value lower than the highest address on the network. To set this 
value via BACnet, write to the Max_Master property of the device object for the E31E’s virtual router.

The final field is the MSTP_MAC_Addr, which sets the MAC address for the virtual router. The E31E panel(s) are devices on the 
internal BACnet network and are not directly addressable as MAC addresses on the MS/TP network.

2. BACnet IP mode

BACnet IP mode uses the same DeviceID_Offset and Virt_Router_Net parameters described above for BACnet MS/TP mode. One 
additional parameter, BACnet_IP_Port, is used to set the UDP port. Most BACnet systems use the default port (47808 decimal, 
0xBAC0 hex) that is recommended in the BACnet standard as the only UDP port. Some large systems need to segment the 
enterprise and use more than port. If so, enter the number of the port you need to use to access this device. BACnet IP mode does 
not use MSTP_Max_Master or MSTP_MAC_Addr. 

BACnet IP mode adds another field called BBMD_Enable. See the section BBMD Support for a full description of how to enable and 
use BBMD support.

Gateway 
Configuration (cont.)

Shop for Power Metering products online at:

1.888.610.7664

www.

PowerMeterStore

.com

Содержание E31A002



























Отзывы: