Vega FIBERTRAC 31 Скачать руководство пользователя страница 84

Страница: 84 / 96

13 Supplement

FIBERTRAC 31 • Profibus PA

43833-EN-170126

•

AI FB1 (OUT)

–

Out value of the AI FB1 after scaling

•

AI FB2 (OUT)

–

Out value of the AI FB2 after scaling

•

AI FB3 (OUT)

–

Out value of the AI FB3 after scaling

•

Free Place

–

This module must be used if a value in the data telegram of the cyclical data traffic should not

be used (e.g. replacement of temperature and Additional Cyclic Value)

A maximum of three modules can be active. By means of the configuration software of the Profibus

master you can determine the configuration of the cyclical data telegram with these modules. The

procedure depends on the respective configuration software.

Note:

The modules are available in two versions:

•

Short for Profibus master supporting only one "Identifier Format" byte, e.g. Allen

Bradley

•

Long for Profibus master only supporting the "Identifier Format" byte, e.g. Siemens

S7-300/400

Examples of telegram configuration

In the following you will see how the modules can be combined and how the appendant data tel

egram is structured.

Example 1

•

AI FB1 (OUT)

•

AI FB2 (OUT)

•

AI FB3 (OUT)

Byte-

No.

For-

mat

IEEE-754-Floating point

value

Sta-

tus

IEEE-754-Floating point

value

Sta-

tus

IEEE-754-Floating point

value

Sta-

tus

Value

AI FB1 (OUT)

FB1

AI FB2 (OUT)

FB2

AI FB3 (OUT)

FB3

Example 2

•

AI FB1 (OUT)

•

Free Place

•

Free Place

Byte-No.

Format

IEEE-754-Floating point value

Status

Value

AI FB1 (OUT)

AI FB1

Note:

Bytes 6-15 are not used in this example.

Содержание FIBERTRAC 31

































































































Результаты поиска

Содержание FIBERTRAC 31

Отзывы:

Бренды по названию

Популярные бренды

Vega FIBERTRAC 31, Руководство по эксплуатации

Результаты поиска

Содержание FIBERTRAC 31

Отзывы:

Бренды по названию

Популярные бренды