Vega FIBERTRAC 31 Скачать руководство пользователя страница 15

Страница: 15 / 96

4 Mounting

FIBERTRAC 31 • Profibus PA

43833-EN-170126

Fasten the sensor in such a way that it cannot fall out of the holder. If

necessary, provide the sensor with a support from below.
Direct the exit angle of the source container to the FIBERTRAC 31.
Mount the source container as close as possible to the vessel. If there

are gaps, secure the area with a safety fence and protective grating

so that no one can reach into the dangerous area.

You can mount the sensor on your vessel with the enclosed mounting

clamps. A number of mounting clamps come with the FIBERTRAC 31

depending on the length of the sensor.
Use a mounting clamp approx. every 450 mm (17.72 in). Adjust the

distances between the attached mounting clips.
Take note of the minimum bending radius of the sensor, which is

305 mm (12 in).

Fig. 4: Mounting clamp
x Hole for screw M8

→

Determine the exact mounting position of one or several mounting

clamps and mark the holes.
Align the mounting positions exactly and average the distances

between the enclosed mounting clamps.
Drill appropriate holes (max. M12) for fastening the mounting

clamps.

Note:

The mounting clamps do not come with fastening screws. Use fasten

ing elements that are appropriate for the situation in your plant.

To measure the level in very high vessels, multiple instruments can be

cascaded.
Cascading means that two or several instruments are connected

which can together cover a longer measuring range.

Mounting clamps

Summation

Содержание FIBERTRAC 31

































































































Результаты поиска

Содержание FIBERTRAC 31

Отзывы:

Бренды по названию

Популярные бренды

Vega FIBERTRAC 31, Руководство по эксплуатации

Результаты поиска

Содержание FIBERTRAC 31

Отзывы:

Бренды по названию

Популярные бренды