Vega FIBERTRAC 31 Скачать руководство пользователя страница 32

Страница: 32 / 96

6 Set up with the display and adjustment module

FIBERTRAC 31 • Profibus PA

43833-EN-170126

Setup

An address must be assigned to each Profibus PA instrument. Each

address may only be assigned once in the Profibus PA network. The

sensor is only recognized by the control system if the address is set

correctly.
When the instrument is shipped, address 126 is set. This address can

be used to test the function of the instrument and to connect it to a

Profibus PA network. Then the address must be changed to integrate

additional instruments.
The address setting is carried out either via:

•

The address selection switch in the electronics compartment of

the instrument (address setting via hardware)

•

The display and adjustment module (address setting via software)

•

PACTware/DTM (address setting via software)

Hardware addressing is effective if an address less than 126 is set

with the address selection switches on the electronics module of

FIBERTRAC 31. In such case, software addressing has no effect -

only the set hardware address applies.

Software addressing is only effective if address 126 or higher is set

on the instrument with the address selection switches.

If a hardware address was adjusted (< 126), then the instrument

signals that the hardware address is active.

In this menu item you can assign an unambiguous name to the sen

sor or measurement loop. Push the "

" key to start the editing. With

the "

" key you change the sign and with the "

>" key you jump to the

next position.

You can enter names with max. 19 characters. The character set

comprises:

•

Capital letters from A … Z

•

Numbers from 0 … 9

•

Special char - / _ blanks

In this menu item you can adjust the FIBERTRAC 31 to the isotope

installed in the source container.

Setup - Sensor address

Hardware addressing

Software addressing

Setup - Measurement

loop name

Setup - Isotope

Содержание FIBERTRAC 31

































































































Результаты поиска

Содержание FIBERTRAC 31

Отзывы:

Бренды по названию

Популярные бренды

Vega FIBERTRAC 31, Руководство по эксплуатации

Результаты поиска

Содержание FIBERTRAC 31

Отзывы:

Бренды по названию

Популярные бренды