manualshive.com logo in svg

Vega FIBERTRAC 31, Руководство по эксплуатации

Поделиться
Скачать
Vega FIBERTRAC 31 Скачать руководство пользователя страница 74

74

11 Diagnostics and servicing

FIBERTRAC 31 • Profibus PA

43833-EN-170126

Error

Reason

Removal

The instrument signals cov

-

ered without covering with the 

medium
The instrument signals cov

-

ered with covering with the 

medium

Voltage supply missing

Check cables for breaks; repair if necessary

Operating voltage too low

Check, adapt if necessary

Electrical connection faulty

Check connection according to chapter 

"

Connection steps

" and if necessary, correct ac

-

cording to chapter "

Wiring plan

"

Electronics defective

Change the switching behaviour of the sensors 

under "Diagnosis/Simulation". If the instrument 

does not switch over, send it in for repair.

Buildup on the inner wall of 

the vessel

Remove buildup
Check the Delta I value.
Improve the switching threshold - carry out a 

double point adjustment

Depending on the reason for the fault and the measures taken, the 

steps described in chapter "

Setup

" must be carried out again or must 

be checked for plausibility and completeness.

Should these measures not be successful, please call in urgent cases 

the VEGA service hotline under the phone no. 

+49 1805 858550.

The hotline is also available outside normal working hours, seven 

days a week around the clock.
Since we offer this service worldwide, the support is provided in 

English. The service itself is free of charge, the only costs involved are 

the normal call charges.

11.4  Exchanging the electronics module

If the electronics module is defective, it can be replaced by the user.
In Ex applications, only instruments and electronics modules with ap

-

propriate Ex approval may be used.
If there is no electronics module available on site, the electronics 

module can be ordered through the agency serving you. The electron

-

ics modules are adapted to the respective sensor and differ in signal 

output or voltage supply.
The new electronics module must be loaded with the default settings 

of the sensor. These are the options:

• 

In the factory

• 

Or on site by the user

In both cases, the serial number of the sensor is needed. The serial 

numbers are stated on the type label of the instrument, on the inside 

of the housing as well as on the delivery note.
When loading on site, the order data must first be downloaded from 

the Internet (see operating instructions manual "

Electronics module

").

Caution:

All application-specific settings must be entered again. That's why you 

have to carry out a fresh setup after exchanging the electronics.

Reaction after fault recti-

fication

24 hour service hotline

Содержание FIBERTRAC 31

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды