TECHNISCHE ANGABEN
26/94
CN929-7015M002
BETRIEBSMODI
Meldungen, die zu den Modustasten gehören
Die MODUS-Taste wird benutzt bis sich der
Strombetriebsmodus des E-Net Dual-Controllers
ändert. Bei Betätigen der MODUS-Taste wird der
Modus Stromeinstellung angezeigt. Bei abwechseln
dem Drücken dieser Taste wird zwischen LOCAL
(LOKAL) und SERIAL (SERIELL) gewechselt.
Um die Schaltung auf REMOTE I/O (FERN-E/A) zu stellen,
müssen die Tasten MODE und CHANGE CONFIG länger
als 2 Sekunden lang gemeinsam gedrückt werden.
O p e r a t
i n g
M o d e
L O C A L
O p e r a t
i n g
M o d e
R E M O T E
I
/ O
O p e r a t
i n g
M o d e
S E R I A L
Die drei LEDs unter dem LCD zeigen den Betriebsmodus
an, in dem sich der Controller befindet.
MERKE
Wenn der H.V. eingeschaltet ist, ist es nicht möglich
den Betriebsmodus des E-Net Dual-Controllers.zu
wechseln.
Hochspannungskommandos
Wenn der E-Net Dual-Controller nach auf dem Modus
LOCAL geschaltet wird, erscheint eine Meldung zu der/den
angewählten Pumpe(n) auf dem LCD.
Wenn der Controller beispielsweise nur zwei HV-Kanäle
hat, erscheint folgende Meldung:
1
5 0 0
D I O D E / N D
2
5 0 0
D I O D E / N D
Um die Hochspannung einzuschalten, müssen erst
sämtliche Anschlüsse (Kabel, Fernschaltung E/A
Verbinder und vordere Schalttafel) geschlossen werden;
dann die Konfig.bearb. und die Hochspannungstasten
On/Off zusammen betätigen.
Die Spannungs- und Druckwerte erscheinen nur dann auf
dem Display, wenn nur eine HV-Karte vorhanden ist.
Wenn zwei HV-Karten vorhanden sind, erscheinen nur die
beiden Spannungswerte.
Wenn nur eine HV-Karte vorhanden ist, erscheint
Folgendes:
1
I I
+ 7 0 0 0
V o l
t
2
I I
+ 7 0 0 0
V o l
t
Das Aufblinken des LED unter dem H.V. On/Off–Taste
informiert den Bediener ununterbrochen, ob
Hochspannung vorhanden ist oder nicht.
Der Einstellungsstatus wird für jeden Kanal durch
,
I
angezeigt, diese bedeuten Aktiv-Einstellung bzw. Nicht-
Aktiv-Einstellung.
Beim Drücken der Taste KONFIG.BEARB. erscheinen die
Strom- und Druckwerte von der Pumpe in Reihenfolge auf
dem Display sowie die Druckwerte von Eyesys-Anzeigen,
wenn sie installiert sind.
Wenn zwei HV-Karten vorhanden sind, erscheint
Folgendes:
1
I I
6
. 5
E - 6
A m p
2
I I
3
. 5
E - 6
A m p
Wenn zwei HV-Karten vorhanden sind, erscheint
Folgendes:
1
I I
3 .
7
E - 9
T o r
r
2
I I
3 .
9
E - 8
T o r
r
Beim Drücken der Taste KONFIG.BEARB. erscheint der
Spannungswertdisplay wieder.
1
I I
L O W
P R E S S U R E
2
I I
L O W
P R E S S U R E