Valet Digital Скачать руководство пользователя страница 51

Страница: 51 / 64

TO DISABLE A DETECTOR FOR ENTRY DELAY

Enter entry delay programming mode:

1. Press the ‘ # ‘ key then enter your 4-digit Pin

Code followed by the number ‘6’ key.

2. You will hear a low tone beep confirming that

the alarm is ready to disable an Entry Delay for

a detector zone

Delete an Entry Delay from a Detector/Zone:

1. Press the ‘ # ‘ key then enter your 4-digit Pin

Code.

2. Press the number of the Detector/Zone you

wish to disable the Entry Delay from.

3. You will not hear beeps for this detector/zone

now because it is disabled. If you have multiple

zones enabled for Entry Delay, The beeps will

indicate the remaining zones that are still

enabled for an Entry Delay.

Example: Zone 1, zone 3 and zone 4 are enabled for

Entry Delay, when you delete zone 3 from the list

you will hear the internal screamer make a single

beep, pause, then make 4 beeps.

Note: This procedure is time dependent. You must do each step within the

allocated time. Test that the operation is correct once programmed. If a

mistake is made, wait 30 seconds and the unit will exit programming mode

then start again.

Содержание Digital

































































Результаты поиска

Содержание Digital

Отзывы:

Похожие инструкции для Digital

Бренды по названию

Популярные бренды

Valet Digital, Инструкция по эксплуатации

Результаты поиска

Содержание Digital

Отзывы:

Похожие инструкции для Digital

Бренды по названию

Популярные бренды