background image

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

MODEL   

L48 (FG00001)

DIRECT VENT  

ZERO CLEARANCE 

GAS FIREPLACE HEATER

MULTIFUNCTION REMOTE (MF)

INSTALLATION INSTRUCTIONS 

AND OWNER’S MANUAL

WARNING

If not installed, operated and maintained 
in accordance with the manufacturer’s 
instructions, this product could expose 
you to substances in fuel or from fuel 
combustion which can cause death or 
serious illness.

This appliance may be installed in 
an aftermarket, permanently located, 
manufactured home (USA only) or mobile 
home, where not prohibited by local 
codes.

This appliance is only for use with the 
type of gas indicated on the rating plate.

This appliance is not convertible for use 
with other gases, unless a certified kit is 
used.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings 
exactly could result in serious injury, 
death or property damage.

 

Do not store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance.

 

WHAT TO DO IF YOU SMELL GAS
•  Do not try to light any appliance.
•  Do not touch any electrical switch; 

do not use any phone in your 
building.

•  Leave the building immediately.
•  Immediately call your gas supplier 

from a neighbor’s phone. Follow 
the gas supplier’s instructions.

•  If you cannot reach your gas 

supplier, call the fire department.

 

Installation and service must be 
performed by a qualified installer, 
service agency or the gas supplier.

DANGER

HOT GLASS

 WILL  

CAUSE BURNS. 

DO NOT TOUCH

 GLASS 

UNTIL COOLED. 

NEVER

 ALLOW CHILDREN  

 TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from 

the hot viewing glass is provided with this appliance 

and shall be installed for the protection of children 

and other at-risk individuals.

NOTE : Barrier required, may be sold separately.

We suggest that our gas 
hearth products be installed 
and serviced by professionals 
who are certified in the U.S. 
by the National Fireplace 
Institute (NFI) as NFI Gas 
Specialist.

WARNING This product can 

expose you to chemicals 

including carbon monoxide, 

which is known to the State of 

California to cause cancer, birth 

defects or other reproductive 

harm. For more information go to   

www.P65warnings.ca.gov/

 

46139A

2019-11-26

Printed in Canada

ENGLISH

Содержание L48





















































































Отзывы: