Vaillant 0010007381 Скачать руководство пользователя

Страница: 36 / 40

Installation and maintenance instructions auroSTEP plus 0020077748_FT1

9 Service/diagnostics

You can access the service/diagnostic level by simulta-
neously pressing the programming button and the knob
for approx. 3 seconds.

Display

Actuators/Sensor values

Test procedure

Test collector pump 1 (solar pump)

Collector pump 1 on, all other actuators off

Test collector pump 2 (booster pump)

Collector pump 2 on, all other actuators off

Test anti-Legionella pump / Bypass-diverter valve

Anti-Legionella pump on, all other actuators off

Electric heating element (EP) test

Test electric heating element on, all other actua-
tors off

C1/C2 contact test

C1/C2 contact closed, all other actuators off

Cylinder temperature display for cylinder sensor 1

Cylinder temperature display for cylinder sensor 2

Temperature display for collector sensor

Table 9.1 Actuator/Sensor test

9 Service/diagnostics

Содержание 0010007381









































Результаты поиска

Содержание 0010007381

Отзывы:

Похожие инструкции для 0010007381

Бренды по названию

Популярные бренды

Vaillant 0010007381, Описание системы, руководство по установке и обслуживанию

Результаты поиска

Содержание 0010007381

Отзывы:

Похожие инструкции для 0010007381

Бренды по названию

Популярные бренды