Vaderstad CR 1225 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 58

background image

Figure 6.5

The spring brake cylinders use a diaphragm cylinder (A)
for the travel brake/parking brake and a spring brake
section (B) for emergency braking.
NOTE: Before using the machine: Check that the screws
(C) on each cylinder are fully tightened, to ensure that the
emergency brakes will be able to operate.

6.2

Switching between transport and
working position

Switching to the transport position must be
carried out on level ground. Do not allow the
machine to lean laterally.

6.2.1

Switching to transport mode

1. Select the neutral gear position or depress the clutch.

Do not apply the service or parking brake. The tractor
must be allowed to roll backwards when the packer is
tilted.

Figure 6.6

2. Raise the front tools.

Figure 6.7

3. Fold out the machine.

For larger tractors and crawler tractors, it is not
enough to simply put them into neutral. Slowly drive
the last part of the folding system backwards to avoid
prying off the tyres.

Figure 6.8

4. Tilt the Packer completely backwards.

Figure 6.9

5. Drive the tractor slowly forward.

903815-en-gb; 23.09.2021

21

«
...
23
24
25
26
27
...
»

Содержание CR 1225



























































Отзывы:

Нет отзывов

Похожие инструкции для CR 1225

Бренд: Oemtools Страницы: 4

Бренд: GE Страницы: 698

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: Garelick Страницы: 4

Бренд: Idmed Страницы: 2

AquaPure Ei Series

Бренд: Jandy Страницы: 4

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: PASCO Страницы: 30

Бренд: GE Страницы: 18

Бренд: Kelso Страницы: 21

Бренд: Daekyung Страницы: 15

Avisa Line XL04

Бренд: FHF Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды