Vaderstad CR 1225 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 58

background image

Hitching and unhitching

5

Hitching and unhitching

5.1

Hitching to the tractor

The tractor must always be switched off during
connection and disconnection of the hydraulic
hoses, otherwise the machine’s hydraulics may
be damaged.

During the work, the machine may give rise to
upward force in the tractor’s hitch device.

Figure 5.1

1. Connect the machine’s drawbar to the tractor’s hitch

device.

2. Raise and secure the machine’s support stand.

3. Connect the hydraulic hoses. Carefully check that the

hoses are connected in pairs to the correct hydraulic
connectors. Carefully wipe the couplings and
connectors. This is a good way to avoid unnecessary
problems and wear in the hydraulic system.

4. Connect the lights.

5. Check that hoses and electrical cables are hanging

freely, even at sharp turns.

Figure 5.2

6. Retract the depth stopper cable into the tractor cab,

see

“8.4 Setting the depth stopper“

.

5.2

Hydraulic support stand

Figure 5.3

The support stand can be set to two different positions.
There is a stay (A) mounted on the bracket to adjust the
foot at the correct angle when the support stand is
mounted in the lower position.

A

903815-en-gb; 23.09.2021

15

«
...
17
18
19
20
21
...
»

Содержание CR 1225



























































Отзывы:

Нет отзывов

Похожие инструкции для CR 1225

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: KBT Страницы: 12

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: natus Страницы: 20

Dantec Keypoint G4

Бренд: natus Страницы: 42

Бренд: natus Страницы: 149

Бренд: R&S Страницы: 2677

Бренд: JBSYSTEMS Light Страницы: 17

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Бренд: UniPix Страницы: 24

Бренд: Abus Страницы: 12

Бренд: Garden Treasures Страницы: 2

Бренд: U-Line Страницы: 6

Бренд: KAPPLER Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды