Vaderstad CR 1225 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 58

background image

Installation

4

Installation

The tractor may not be hitched to the machine if
the maximum permitted total weight or axle load
for the tractor is exceeded.

The load on the tractor’s front axle may not be
less than that specified.

All basic settings and adjustment must always be
carried out on a level surface with the machine
hitched to the tractor and the wing sections
folded down.

4.1

Tractor requirements

If the K80 model ball coupling is to be used, ensure that
the tractor’s hitch device can withstand negative ball
pressure.

4.2

Tractor hydraulic system
requirements

Hydraulic connectors

The tractor must have:

•

3-4x double-acting hydraulic connectors, depending
on the equipment option.

See chapter

“5.3.1 Dimensions and colour coding on the

hydraulic hoses“

for more detailed information.

Oil temperature

Väderstad recommends that the temperature of the
hydraulic oil during operation be kept between 40 and
60° C for best performance and longevity.

Hydraulic oil temperature

0 ºC

40 ºC

60 ºC

80 ºC

3

2

1

2

3

1. Recommended temperature range for hydraulic oil.

2. Outside the recommended temperature range for the

hydraulic oil.

3. Hydraulic oil temperature without guaranteed

function and with reduced life expectancy.

Viscosity

Väderstad recommends that the viscosity of the hydraulic
oil during operation is kept between 20 and 50 cSt for
best performance and longevity.

Viscosity

400 cSt

50 cSt

20 cSt

10 cSt

3

2

1

2

3

1. Recommended viscosity range for hydraulic oil.

2. Outside the recommended viscosity range for the

hydraulic oil.

3. Hydraulic oil viscosity without guaranteed function

and with reduced life expectancy.

Purity

Väderstad AB recommends a hydraulic oil purity of 18/
16/13 according to ISO 4406 for best performance and
longevity.

Oil quality

Väderstad recommends that mineral oil be used in
accordance with ISO VG 46–68.

Pressure levels

Väderstad AB recommends a maximum pressure level of
200-210 bar. The pressure will drop slightly when
continuous hydraulic power is taken out, however it
should not drop below 190 bar in order to maintain the
best performance.

The free return connection must have a maximum
pressure of 6 bar.

14

903815-en-gb; 23.09.2021

«
...
16
17
18
19
20
...
»

Содержание CR 1225



























































Отзывы:

Нет отзывов

Похожие инструкции для CR 1225

Бренд: Calistair Страницы: 44

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: JB-Lighting Страницы: 60

LOUDEN 200 Series

Бренд: ACCO Brands Страницы: 144

Бренд: B&K Страницы: 16

Бренд: B&G Страницы: 2

Бренд: R.M. Young Страницы: 10

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды