Vaderstad CR 1225 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 58

background image

General settings

7.4.2

Scraper blades

Figure 7.13

The machine is delivered with standard type scraper
blades (A).

Wider points (B) may be ordered. The part number for
these points is indicated in the spare parts manual.
The wider point is designed for clay soils and moist
conditions with little occurrence of straw, e.g. when
working in very moist, ploughed clay soil.

7.4.3

Middle section

Figure 7.14

The scrapers on the centre section can be adjusted
lengthwise by repositioning the scraper unit in the oblong
holes in the holders under the frame.

1. Loosen the bolted joints (A) and adjust to the desired

position.

2. Tighten the bolted joints.

7.4.4

Wheel section

Figure 7.15

Figure 7.16

1. The scrapers on the wheel sections can be adjusted by

turning the tube along the groove in the holder.
Loosen the nut (A) and set to the desired position.

2. Retighten the nut.

7.5

Front tools

7.5.1

CrossBoard

The hydraulics system should be synchronised before any
adjustments are made. See

“9.6.1 Synchronising the

series-connected hydraulics system“

A

B

A

A

28

903815-en-gb; 23.09.2021

«
...
30
31
32
33
34
...
»

Содержание CR 1225



























































Отзывы:

Нет отзывов

Похожие инструкции для CR 1225

Бренд: NARGESA Страницы: 50

Бренд: YardCraft Страницы: 17

Бренд: Obdstar Страницы: 10

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: EuroLite Страницы: 28

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды