Unipulse F320 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 129

Unipulse F320 Скачать руководство пользователя страница 6

SAFETY PRECAUTIONS

CAUTION

●

Use the F320 as it is incorporated in a control panel, etc.

●

Do not install in the following environments.

- Where the temperature/humidity exceeds the range of the specifications.
- Outdoors, or where the altitude exceeds 2000m.
- Places containing large quantities of salt or iron powder.
- Where the main body is directly affected by vibrations or shocks.

●

Take adequate shielding measures when using at the following locations.
- Near a power line.
- Where a strong electric field or magnetic field is formed.
- Where static electricity, relay noise or the like is generated.

●

Tighten the screws for the signal input/output terminals at the specified torque.

　

If they are loose, shorts, fire or malfunctions may occur.

Tightening torque: 0.2 – 0.6N•m

●

For sensors, external inputs/outputs and options, use shielded cables.

●

For turning on/off the power, be sure to keep intervals of 5 seconds or more.

●

If the F320 is not used by the specified method, its protective performance may be

impaired.

●

When the F320 is shipped, spacers made of corrugated cardboard are used as
cushioning materials.
Though it is factory-designed so that shocks can sufficiently be absorbed, breakage
may result if shocks are applied when the spacers are reused for transportation. If you
send the F320 to us for repair, etc., take adequate measures against shocks by using
polyurethane materials, etc., separately.

●

If you dispose of the product, handle it as industrial waste.

Caution on installation

Caution on wiring

Caution during startup and maintenance

Caution during transportation

Caution during disposal

«
...
4
5
6
7
8
...
»

Содержание F320


































































































































Отзывы:

Нет отзывов