Unipulse F320 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 129

background image

11.D/A CONVERTER

94

11-2. Current Output (DAI Option)

This converter is used to obtain an analog output which is linked with the
indicated value of the F320.
The range of the analog output is from 4 to 20mA.
An analog output from 4mA to 20mA can be obtained with respect to any digital
values set by the D/A zero setting and the D/A full scale setting functions.
The output circuit and the main circuit are isolated.

Current output:

4 to 20mA (load resistance; 350

Ω

or less)

D/A conversion speed:

2000 times/sec.

Resolution:

1/10000

Over range:

3.2 to 20.8mA

Zero adjustment range: Approx. 3.6 to 4.4mA (at the time of zero output)
Gain adjustment range: Approx. 19.6 to 20.4mA

(at the time of full scale output)

Zero drift:

Within 0.5µA/

℃

Gain drift:

Within 50ppm/

℃

Non-linearity:

Within 0.05%FS
* Not including the drift of the analog input section

Output connector:

Screw type terminal block (two-pole)

㨆㧱㧾㧻㧳㧭㧵㧺

㧗

Current output terminals

Terminals for obtaining current signal.
“+” is for signal, and “-” is for ground.
4 to 20mA can be obtained.

+ -

Gain adjustment
trimmer

Trimmer to adjust so
that the indication
becomes as registered
by the D/A full scale
setting function.
The gain adjustment
range is approx. 19.6
to 20.4mA (at the
time of full scale
output).

Zero adjustment trimmer

Trimmer to adjust so that the current output becomes
zero when the indication is as registered by the D/A
zero setting function.
The zero adjustment range is approx. 3.6 to 4.4mA
(at the time of zero output).

«
...
106
107
108
109
110
...
»

Содержание F320


































































































































Отзывы:

Нет отзывов

Похожие инструкции для F320

Бренд: Xylem Страницы: 24

Бренд: Gardner Bender Страницы: 7

Бренд: M & I Instruments Страницы: 2

Бренд: ZHYQ Страницы: 6

Smart Probes 115i

Бренд: TESTO Страницы: 17

Бренд: TA Instruments Страницы: 68

Бренд: Fora Страницы: 64

Бренд: LaserLiner Страницы: 64

Бренд: PCE Health and Fitness Страницы: 66

Бренд: Fluke Страницы: 97

PROline promag 23

Бренд: Endress+Hauser Страницы: 108

Бренд: Analog Devices Страницы: 40

Бренд: Hach Страницы: 74

Бренд: Befaco Страницы: 3

Бренд: Midtronics Страницы: 30

Бренд: PCE Instruments Страницы: 10

Бренд: Sunrise Manufacturing International Страницы: 118

Бренд: Parma Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды