Ulvac C30MVER Скачать руководство пользователя | Manualshive

Страница: 80 / 110

background image

C30VR Compressor Installation, Operation, Maintenance and Troubleshooting

7-2

ULVAC CRYOGENICS INCORPORATED

Adsorber replacement procedure is shown below.

1. Ensure that each equipment and device in cryopump system is safe to replace

adsorber.

2. Turn off the compressor unit by turning OFF the breaker inside the distribution panel at

the equipment side. Lock the breaker in the OFF status for safety reasons.

3. Disconnect the flexible hoses from the “SUPPLY GAS” and “RETURN GAS”

connectors at the rear panel of the compressor. Observe the disconnecting
requirements below. Refer to “Section 4.3 Connecting and disconnecting helium
flexible hoses” for disconnecting method.

NOTE:

When disconnecting flexible hoses from the connectors, use two single-ended

wrenches (bolt width 26mm, 30mm).

4. Remove the nuts of the connectors at the rear panel of the compressor with the

spanner (Figure 7-1).

5. Remove the seven screws of the rear panel with a proper screw driver and remove the

rear panel (Figure 7-2 and 7-3).

6. Disconnect the self-sealing coupling from the adsorber with two spanners.The coupling

is connected to the flexible hose above the bottom plate inside the compressor chassis
(Figure 7-4). See Figure 7-5 for usage of spanners to disconnect the coupling.

Disconnect the coupling quickly to minimize minor helium leakage.

7. Remove the bolts that secure the adsorber to the base of the compressor with the

proper spanner (Figure 7-6).

WARNING

Inside the compressor unit, some areas remain hot immediately after the shutdown.
Wait for at least 15 minutes in order to perform maintenance work safely. Failure to
observe this warning may result in severe body injury.

hen adjusting helium pressure, it is nece

the work while inside of the

ompressor unit is in room temperature.

ork after cooling down the

ompressor for three hours.

W

ssary to perform

Perform this w

c
c

Do not disconnect flexible hoses while the cryopump is in low temperature. Doing so
may raise the internal pressure as inside of the refrigerator unit warms up, resulting in
helium leakage by activated safety valve.

CAUTION

«
...
78
79
80
81
82
...
»

Содержание C30MVER















































































































Отзывы:

Нет отзывов

Похожие инструкции для C30MVER

ENDURO 145 COMPRESSOR

Бренд: Lavor Страницы: 8

Бренд: Frick Страницы: 78

Бренд: Perel Страницы: 12

Бренд: Strend Pro Страницы: 64

Бренд: Outbac Страницы: 3

S261R-LD1-115PD

Бренд: C-Aire Compressors Страницы: 12

Бренд: Synairgy Страницы: 12

Бренд: Atlas Copco Страницы: 88

Бренд: GEA Bock Страницы: 28

Бренд: GEA Bock Страницы: 34

Бренд: KAESER KOMPRESSOREN Страницы: 24

PRO A29B-0 150 CM3 Zero

Бренд: ABAC Страницы: 100

Бренд: Eastwood Страницы: 20

Бренд: Campbell Hausfeld Страницы: 24

Бренд: Unitec Страницы: 12

Бренд: BendPak Страницы: 48

Бренд: sunjoe Страницы: 20

Бренд: sunjoe Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды