Ulvac C30MVER Скачать руководство пользователя

Страница: 5 / 110

MZ0F001E,2013OR03

ULVAC CRYOGENICS INCORPORATED

F-3

2.3 Repair period after production is discontinued

ULVAC CRYOGENICS shall accept product repairs for seven years after

production of the product is discontinued.

3. Service Form

After the products are delivered, please fill out the following information in the

blanks. If you have any questions or technical problems

please feel free to contact

the nearest Customer Support Center or headquarters. Please refer to “Service

Network”.

Cryopump

／

Super trap Model

：

Cryopump

／

Super trap Serial No.

：

Refrigerator Model

：

Refrigerator Serial No.

：

Compressor Model

：

Compressor Serial No.

：

Temperature controller

／

Thermal display Model

：

Temperature controller

／

Thermal display

Serial No.

：

Option Part Model

：

Optional Part Serial No.

：

4. Notes for repair and maintenance requests

We may decline your request for the repair or the maintenance of our products if

you refuse to give us information about the presence of the hazardous substance

and/or contaminant.

Also, please be aware that we do not accept liability for damages by the

contaminant, which might be caused during transportation to our office or the

nearest customer support center. To avoid such accident, please pay careful

attention to packing of the product

．

In case of breakdown and accident

When breakdown or accident occurs, we may ask for keeping the product on site

as it is or retrieving the product to investigate its cause. Also we may ask for

reporting the detailed process and/or the operating condition. When unidentified

malfunction was generated, please contact our Service Engineering Division or

Содержание C30MVER















































































































Результаты поиска

Содержание C30MVER

Отзывы:

Похожие инструкции для C30MVER

Бренды по названию

Популярные бренды

Ulvac C30MVER, Инструкции по установке, эксплуатации, техническому обслуживанию и устранению неисправностей

Результаты поиска

Содержание C30MVER

Отзывы:

Похожие инструкции для C30MVER

Бренды по названию

Популярные бренды