Ulvac C30MVER Скачать руководство пользователя | Manualshive

Страница: 50 / 110

background image

C30VR Compressor Installation, Operation, Maintenance and Troubleshooting

3-2

ULVAC CRYOGENICS INCORPORATED

3.3 Unpacking

Use handling equipment such as a forklift for carrying the compressor.

Forklift is needed to remove the compressor from its shipping carton.
The procedure is shown below.

1. Cut the two straps of the carton.

2. Lift the cardboard straight up and remove it from the bottom plate.

3. Insert the forks of the forklift between the bottom of the compressor and the bottom

plate from the side of the compressor. (See Figure 3-2)

4. Ensure that the forks are inserted far enough to protrude from the other side and are

well balanced.

5. Lift the compressor smoothly and move to a flat floor surface and bring down the

compressor without shaking and/or jolting. After putting down the compressor on the
floor, move it to the installation site by hand using the casters provided.

Compress weighs 121 - 131kg. Use handling equipment such as a forklift to move or lift
the compr

. Only authorized personnel familiar with handling and risks of the equipment

or

essor

can operate the handling equipment. Personnel except for the operator of the handling
equipment

st keep away from the handling equipment and the compressor during the

handling. There are risks of dropping an

er of the compressor. Failure to

bse ve this warning may result in severe bodily injury or fatal accident.

mu

d/or tipping ov

o

r

CAUTION

When cutting the straps, handle a cutter with care and be aware of the flailing movement of
the cut straps. Failure to observe this warning may result in severe bodily injury.

CAUTION

After the compressor has been placed at an installation site, ensure to lock all casters of the
compressor to prevent bodily injury by from unexpected movement or slipping of the
compressor. Take adequate measures to prevent overturning of the compressor from
earthquakes as needed. If it is required to mount clamps or brackets on the compressor,
please cont t our Service Engineerin

fer to section 1 Figure 1-8 for an

example of anchor bolt mounting pos

g brackets are mounted on the

ac

g Division. Re

ition when fixin

compressor.

CAUTION

Bring down and place the compressor on the flat floor to avoid the compressor slipping. If
the floor is sloped the compressor may move this could result in severe bodily injury or fatal
accident.

CAUTION

«
...
48
49
50
51
52
...
»

Содержание C30MVER















































































































Отзывы:

Нет отзывов

Похожие инструкции для C30MVER

SALTER AIRE Plus 8350

Бренд: Salter Labs Страницы: 9

Бренд: MPS Страницы: 2

Бренд: Danfoss Страницы: 60

Бренд: Hanbell Страницы: 51

Бренд: Johnson Controls Страницы: 60

SBBHS030020SD10

Бренд: Powerex Страницы: 12

300/10/50 14 TLG

Бренд: Gude Страницы: 32

Бренд: VIAIR Страницы: 8

Бренд: VIAIR Страницы: 8

Бренд: VIAIR Страницы: 10

Бренд: L&W Compressors Страницы: 197

Бренд: KAESER Страницы: 348

Бренд: YATO Страницы: 40

Бренд: Valeo Страницы: 47

Бренд: Campbell Hausfeld Страницы: 60

Mi Portable Electric Air Compressor

Бренд: Xiaomi Страницы: 16

Бренд: Makita Страницы: 292

Бренд: Gardner Denver Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды