Ulvac C30MVER Скачать руководство пользователя

Страница: 105 / 110

Appendix D

C30V

R Compressor Flow Diagram

ULVAC CRYOGENICS INCORPORATED

D-1

Appendix D C30V

R Compressor Flow Diagram

Low pressure helium gas returning from the refrigerator unit enters the compressor.

Lubricant oil is injected into the compressor with the low pressure helium; the gas

containing the oil is then compressed by the compressor pump turning it into high

temperature high pressure helium gas. Most of the lubricant oil returns to droplet form

and is separated within the compressor. This lubricant oil is pooled at the bottom and

lubricates the inside of the compressor. It follows the circulating system where it

comes out from the compressor and cooled down at an oil heat exchanger before being

injected back into the compressor through an oil injection filter.

High temperature high pressure helium gas comes out from the compressor, passes

through a water cooled helium heat exchanger for removal of compression-caused heat.

It is cooled to an ambient temperature and then enters an oil separator. In here, the oil

is separated and the droplets of separated oil pass thorough an oil return filter and oil

return orifice before joining the low pressure helium gas and being returned to the

compressor. High pressure helium gas comes out from the oil separator enters an

adsorber where oil-mist is adsorbed and removed. The Helium gas comes out the

adsorber passes through a flexible hose and is supplied to the refrigerator unit.

◆

Compressor safety devices

Name Function Specification

Safety valve

※

Located on the helium supply line and

releases gas automatically when pressure

exceeds the set value.

Set pressure

：

2.55MPaG

Differential

pressure

regulating valve

Located on the line connecting helium

supply and return lines and automatically

keeps the high

–

low differential pressure

under the set value.

Set pressure

：

1.74MPa

※

The set pressure of safety valve at the refrigerator is 1.9MPaG. Please note that

the refrigerator safety valve releases gas before the compressor safety valve in actual

system.

Содержание C30MVER















































































































Результаты поиска

Содержание C30MVER

Отзывы:

Похожие инструкции для C30MVER

Бренды по названию

Популярные бренды

Ulvac C30MVER, Инструкции по установке, эксплуатации, техническому обслуживанию и устранению неисправностей

Результаты поиска

Содержание C30MVER

Отзывы:

Похожие инструкции для C30MVER

Бренды по названию

Популярные бренды