Ulvac C30MVER Скачать руководство пользователя | Manualshive

Страница: 45 / 110

background image

Section 2

Considerations before Installation

(b) When the reboot command of the compressor is emitted within 0.3 second from

the operation stop command

(c) When a short power interruption for less than 2 seconds has occurred

In case of the above (a), it takes a few seconds for the compressor to initialize after it

is powered on. Therefore the compressor will neither recognize nor output any remote
signal with the equipment for a maximum of 5 seconds. For reference, the signal
delay when powered on in Alternate operating mode is shown in Figure 2-9.

INPUT POWER SUPPLY

COMP START/STOP

CH1 REF

COMP RUN

CH1 ACK

≧5seconds

Figure 2-9

Signal delay when powered on

（

In Alternate operating mode

）

In the cases of (b) and (c), the answer-back signal is also delayed for a maximum of 5
seconds to respond to the command of “COMP RUN”. This is because the
compressor pump waits to begin its operation until the helium pressure inside
becomes stable. For references, Figure 2-10 shows the signal delay occurred in
Alternate operating mode when the time period from a stop to a reboot is short, and
Figure 2-11 shows the timing chart of C30VR when a short power interruption has
occurred in Momentary operating mode.

From the above-mentioned, the set value of the timeout of the answer-back signal

should be determined based on the condition in which only the compressor has
detected a short power interruption although a user’s equipment is not detecting it
because of differences of the specifications. In this condition, the equipment must
recognize that the compressor is out of order because the equipment side can't
receive the answer-back signal. If dispatch of the answer-back signal will be late for a
preset timeout time even if the compressor has restarted after recovery of the input
power, an alarm of a stop will come out.

Therefore, be sure to set the timeout time of an answer-back signal as 8 seconds or

more in order to monitor the operating conditions of the compressor correctly.

Note: Figure 2-11 leads the following equation:

td + tw + 1

<= 2+ 5 + 1 = 8 (seconds)

Where, “1” second is a margin added.

ULVAC CRYOGENICS INCORPORATED

2-13

«
...
43
44
45
46
47
...
»

Содержание C30MVER















































































































Отзывы:

Нет отзывов

Похожие инструкции для C30MVER

Бренд: MESTIC Страницы: 20

Бренд: Rietschle Страницы: 40

SIGMA CONTROL SMART MOBILAIR M82

Бренд: KAESER KOMPRESSOREN Страницы: 418

Бренд: BE Страницы: 24

Бренд: Atlas Copco Страницы: 94

Бренд: Fini Страницы: 40

Бренд: Gast Страницы: 8

Бренд: Grizzly Страницы: 28

Бренд: Grizzly Страницы: 40

Бренд: Grizzly Страницы: 44

Бренд: HSS Hire Страницы: 2

Бренд: Panduit Страницы: 8

AirSmart EAU99T

Бренд: Gardner Denver Страницы: 77

Бренд: York Страницы: 44

Бренд: ACC Страницы: 20

Бренд: Industrial Air Страницы: 25

Бренд: Unitec Страницы: 12

Бренд: Gardner Denver Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды