background image

30A135

ULTRAFRYER® LIMITED WARRANTY

Ultrafryer Systems warrants to the original purchaser of a gas or electric Ultrafryer® sold within the United States, it’s ter-
ritories and Canada, that it will be free of defects in material and workmanship for the periods listed below:

STAINLESS STEEL FRYER VAT

 – 

Stainless Steel fryer vats are warranted for (10) ten years upon the terms hereinafter 

described. The (10) ten year warranty coverage applies ONLY to the Stainless Steel fryer vat and does not apply to the other com-
ponents such as controls, fire boxes, gaskets, mounting hardware, or the heat shield weldment. The (10) ten year limited warranty 
coverage for the Stainless Steel fryer vats are as follows: (1) Vats that fail due to faulty workmanship or materials within the first 
twelve (12) months from the date of initial start up will be exchanged at no cost. Standard delivery ground freight will be prepaid 
by Ultrafryer 

Systems for first year failures only

. The cost of labor to install the replacement vat will be covered by Ultrafryer 

Systems for vats, which fail within twelve (12) months from the date of initial start up.  Labor for vat replacements after the first 
year is the responsibility of the owner.
(2) Vats that fail within the first (18) months will be exchanged at a cost not to exceed $100.00 FOB San Antonio. (3) Vats that fail 
within the first (24) months will be exchanged at a cost not to exceed $150.00 FOB San Antonio. (4) Vats that fail within the next 
(8) years will be exchanged at a cost not to exceed $200.00 FOB San Antonio. (Subject to inflation adjusted in accordance with 
the C.P.I.).  Proper credit issue for vat failures is contingent upon receipt, by Ultrafryer Systems, of the serial number identifica-
tion tag for any failed vat.

ULTRAFRYER PARTS

 

– 

All parts on the Ultrafryer® are covered for a period of one (1) year from the initial date of start up. 

This is to include computers, gas valves, switches, thermostats, etc. Ultrafryer Systems reserves the right to charge for certain parts 
such as computers, filter pumps and motors or any item over the amount of $100.00 until Ultrafryer Systems receives the defec-
tive part back

 After inspection, credit for the part will

 

be issued to the purchaser provided the part is deemed defective and that 

defect is not the result of neglect or abuse by the user. The shortening filtration system, (hoses) are warranted for ninety (90) days 
from the initial date of start up. 

PROCESSING WARRANTY CLAIMS

 – 

The equipment owner must promptly notify Ultrafryer Systems Warranty Depart-

ment of any alleged defects as soon as they are discovered by calling 1-800-525-8130. After such notice, the Warranty Depart-
ment will perform its obligation under this warranty within a commercially reasonable period of time. If alleged defects develop 
after normal business hours, on weekends or on holidays the owner must call Ultrafryer Systems first at the above number. This 
number is monitored 24 hours a day, 7 days a week. Ultrafryer Systems will notify an authorized service agent to make repairs 
during normal hours or after hours. Any parts that need to be shipped back to Ultrafryer Systems will be shipped back 

prepaid 

by the customer

 marked with the processing number and to the

 

attention of the WARRANTY DEPARTMENT.  

NON WARRANTY COVERAGE

 – 

This warranty does not include coverage for any consequential cost of damages including, 

but not limited to, any loss in store sales, spoiled food products, transportation, duty or custom cost. This warranty does not 
cover the Ultrafryer® exported to countries outside the United States and its territories. This warranty does not cover original 
installation and adjustments such as leveling, calibrations, electrical and gas connections, or problems due to faulty or contami-
nated gas supply. This warranty does not cover travel over 100 miles or 2 hours driving time from the location of the Ultrafryer® 
or overtime or holiday charges unless the Warranty Department granted prior approval. This warranty does not cover damage 
due to misuse, abuse, alteration or accident. This Warranty does not cover improper or unauthorized repair or installation, 
damage in shipment, normal maintenance items such as gaskets, hoses, and exterior finishes. 

Ultrafryer Systems reserves the 

right to void component part warranty on any Ultrafryer® that is stored more than 6 (six) months after shipment from 
Ultrafryer Systems and not put into service. 

LABOR COVERAGE – 

The cost for labor to replace parts are covered for one (1) year after the initial start up. This warranty 

will include the labor involved in the six (6) month and the twelve (12) month fryer inspections

 

recommended by the manufac-

turer for the first year after initial start up

. The Warranty Department must be promptly notified of any defects within the first 

year of operation. 

The labor warranty does not include the cost to repair or clear dirty

 

filter systems or perform any adjustments 

that would normally fall

 

under the tasks associated with a proper start up and/or demonstration

.

  

Labor is covered by Ultrafryer 

Systems for repairs by an AUTHORIZED service agent

.  Owner is responsible for all costs associated with fryer installation and 

start up unless prior arrangements have been made with Ultrafryer Systems.

 

DISCLAIMER OF WARRANTIES

Other than as stated herein ULTRAFRYER SYSTEMS makes no warranty of any kind, express or implied, including but not 
limited to any warranty of merchantability of fitness for a particular purpose, including trade usage. Ultrafryer Systems sole 
obligation, and purchaser’s sole remedy, under this warranty is repair or replacement, at the discretion of Ultrafryer Systems, 
of any part or component that proves to be defective in materials or workmanship. In no event shall Ultrafryer Systems be 
liable for consequential, incidental, or special loss or damages arising from the use of, or inability to use, the ULTRAFRYER®. 
This limited warranty is the only and complete statement with respect to warranties of NEW Ultrafryer® PAR-2, PAR-3 
Gas and Electric ULTRAFRYERS® sold after March 1st, 2001. There are no other documents or oral statements for which 
Ultrafryer Systems will be responsible.

        A. Warranty

Page 2 of 61

Содержание PAR-3-HE


































































Отзывы: