ULTRAFRYER Systems PAR-3-HE, Руководство по эксплуатации

Страница: 46 / 65

30A135
B. POLISHING SHORTENING
1 Set a timer for the amount of time established for POLISHING shortening, then turn the VAT SHORTENING RETURN
LEVER 1/4 TURN COUNTER CLOCKWISE to allow shortening to circulate through the system to POLISH the shortening.
CAUTION: DO NOT POLISH THE SHORTENING MORE THAN THE ESTABLISHED TIME AS IT WILL PUMP
EXCESS AIR INTO THE SHORTENING CAUSING SHORTENING BREAKDOWN.
2. At the end of the established time, TURN the VAT SHORTENING RETURN LEVER 1/4 TURN CLOCKWISE , turn the
DRAIN VALVE HANDLE to the closed UP position; replace the grill in the fryer; then TURN the Vat Shortening RETURN
LEVER 1/4 COUNTER CLOCKWISE to automaticlly return shortening in the filter tub to the fryer vat.
3. When all shortening in the filter tub has been returned to the fryer, TURN the VAT SHORTENING RETURN LEVER , 1/4
TURN CLOCKWISE check and if necessary add fresh shortening so shortening is level with the middle line of the letter “E”
in the word LEVEL of the shortening level mark on the rear wall of the fryer.
4. Remove the Filter Tub Assembly by pressing the DOCKING RELEASE HANDLE and pulling the STANDPIPE DOCKING
HANDLE ASSY away from the FEMALE Bulkhead Socket adjacent to the Drain Valve; then THOROUGHLY clean,
assemble and replace the Filter Tub Assembly in the fryer cabinet.
SHORTENING DISPOSAL, BOIL-OUT& SHORTENING INSTALLATION
A. GENERAL -T he Model PAR-3-HE Gas Fryer should be BOILED-OUT every 7 DAYS to remove carbon buildup and other
encrusted material.
B. SHORTENING DISPOSAL
1. CAREFULLY assemble the Filter Tub assembly according to paragraph A page 38 and CAREFULLY install it in the fryer
cabinet according to paragraph B page 38.
CAUTION: PRIOR TO PROCEEDING TO THE NEXT STEP, PUT ON SAFETY GOGGLES, NEOPRENE INSULATED GLOVES
AND AN APRON.
2. Turn the Toggle ON/OFF switch and Manual Gas Valve OFF, and ensure the filter tub is properly DOCKED beneath the
fryer drain valve.
NOTE: Pull on the filter tub to ASSURE the male docking plug is SEATED in the female bulkhead socket.
3. Attach the Drain Valve Handle to the drain valve; then open the drain valve by turning the DRAIN VALVE HANDLE
slightly downward. When the bottom of the filter tub is covered with about two (2) inches of shortening, completely
OPEN the drain valve, and while shortening is draining, scrape all sides of the vat to remove encrusted material using a
scraper.
4. When all shortening has drained into the filter tub, use the DRAIN ROD to place the wire rack on one side of the vat.
5. Use the drain rod to pull sediment on the bottom of the vat towards the drain valve opening and push it through the valve
opening.
6. Use one (1) of the following procedures to FLUSH sediment and debris from the fryer vat:
a. Fryer WITHOUT an Automatic Vat Cleaner:
1) CAREFULLY connect the Wash Down Hose MALE In-Line Plug to the TOPSIDE FEMALE SOCKET and place the
Wash Down Hose into the vat and hold it firmly against an inner wall so it will not “recoil” upward when the pump
comes ON.
2) TURN the Topside Shortening Return Lever 1/4 turn counter clockwise and hold the wand hose nozzle at a 45º
angle from the bottom of the fryer causing sediment and debris to bounce off the rear wall of the vat and flow
towards the drain valve.
3) Use the “L” shaped vat brush to push the sediment through the drain valve to keep the drain clear. Hose off the
burner tubes and all walls of the vat until all the sediment and residue at the bottom of the fryer has been flushed
through the drain into the filter tub. Then turn theTopside Shortening Return Lever 1/4 turn clockwise.
b. Fryer WITH an Automatic Vat Cleaner (AVC):
1) CAREFULLY position the AVC (SPRAY BLASTER) on the fryer and SECURELY connect the MALE In-Line Plug
on the Spray Blaster flexible hose to the TOPSIDE FEMALE SOCKET.
2) TURN the Topside Shortening RETURN EVER 1/4 TURN COUNTER CLOCKWISE to allow shortening in the
filter tub to be discharged in the vat through the four (4) nozzles in the bottom of the Spray Blaster flushing sedi-
ment and debris through the drain valve.
Page 42 of 61