Ultraflex Power A Mark II Скачать руководство пользователя страница 32

Страница: 32 / 36

Owner's manual

ULTRAFLEX

page 32

of 36-

POWER A MK2

ISH

4 SAFETY WARNINGS

This section shows the safety rules which must be followed for the correct equipment operation.

We recommend reading this section and the other manuals supplied with the steering system components

carefully.

4.1 Safety standards during installation and use

RESPECT STRICTLY the following safety rules:

ULTRAFLEX

declines all responsibility in case the user does not follow these rules and it is not responsible for

negligence during the use of the system.

DO NOT PUT HANDS BETWEEN THE MOVING PARTS.

- Do not disable the safety devices.
- Do not modify or add devices to the system, without

ULTRAFLEX

written authorisation or technical

intervention which will prove the modification.

- Do not use the equipment for a purpose different from the one it has been designed for, which is

specified in the installation and maintenance manual.

- Do not let non-specialized staff perform the installation.

DANGER

WARNING

- When the system is installed, clean thoroughly to prevent foreign bodies from entering it. Even the

smallest object could damage the system permanently.

- Avoid contact between cables and heat sources.

During installation, inspection or maintenance, IT IS STRICTLY FORBIDDEN to wear necklaces, bracelets or

clothes which could get caught in the moving parts.

4.2 Clothing

WARNING

Содержание Power A Mark II





































Результаты поиска

Содержание Power A Mark II

Отзывы:

Похожие инструкции для Power A Mark II

Бренды по названию

Популярные бренды

Ultraflex Power A Mark II, Руководство пользователя

Результаты поиска

Содержание Power A Mark II

Отзывы:

Похожие инструкции для Power A Mark II

Бренды по названию

Популярные бренды